Results 211 to 220 of about 131,366 (311)

Comparative Experimental Study of Eco-Composite Reinforced Concrete Beams Under Flexural Loading: Sustainability Factors vs. Mechanical Performance. [PDF]

Polymers (Basel)
Bounjoum Y, Hamlaoui O, Bibridne Y, Tozan H, Duzdar I, Bouktib N, Choab N, El Fqih MA.   +7 more
europepmc   +1 more source

Development of Cost‐Effective and Highly Transparent Melamine Formaldehyde Resin Modified With Sodium Chloride for Enhancing Glossiness and Abrasion Resistance of Melamine Impregnated Paper

Polymer Engineering &Science, EarlyView.
An eco‐friendly melamine‐formaldehyde was produced by the addition of sodium chloride as a modifier. Modified MF resin improved surface gloss and abrasion resistance of decorative paper and decreased the formaldehyde emission. Curing time of the MF resin decreased with the addition of sodium chloride.
Saeed Kamrani, Antonio Pizzi, Peyman Ahmadi, Nadir Ayrilmis, Ali Dorieh, Adam Sikora, Štěpán Hýsek, Kateřina Hájková, Meysam Mehdinia   +8 more
wiley   +1 more source

Study on the strength properties of coir fiber reinforced concrete containing waste brick powder dust as sand replacement. [PDF]

Sci Rep
Palaniappan M, Anandaraj S, Murugesan T, Gebreyohannes DT.   +3 more
europepmc   +1 more source

Investigation of Crystal Structure Change and Mechanical Properties of 3D Printed PLA After Annealing

Polymer Engineering &Science, EarlyView.
Thermal annealing of FDM‐printed PLA significantly enhances longitudinal tensile and flexural strengths by increasing crystallinity to 46.6%. However, transverse properties remain constrained by weak interlayer adhesion, providing crucial insights into the anisotropic thermo‐mechanical behavior of printed biopolymers for demanding engineering ...
Huseyin Erdem Yalkin, Ayse Nur Ozkan
wiley   +1 more source

Mechanical, tribological, and physical performance of sisal fiber reinforced epoxy composites filled with Aningeria, Cordia Africana, and Cedar Sawdust. [PDF]

Sci Rep
Abay JG, Fetene BN, Sufe G.
europepmc   +1 more source

Comparing the Applicability of State‐Of‐The‐Art Photopolymer Injection Molds Printed by Multi‐Material Jetting and High‐Performance Digital Light Processing

Polymer Engineering &Science, EarlyView.
The workflow of comparing state‐of‐the‐art photopolymers in rapid tooling. ABSTRACT Additive manufacturing (AM) introduced the concept of layer‐by‐layer manufacturing, which allows the fast and direct production of parts. Additive technologies are also hybridized with conventional polymer processing technologies.
Szabolcs Krizsma, András Suplicz
wiley   +1 more source

Synergistic Strengthening and Toughening of 3D-Printed Bioinspired Alumina Composites with a Multi-Scale Bouligand Structure. [PDF]

Biomimetics (Basel)
Wang Z, Duan D, Yang L, Bai X, Jiao Z, Wu C, Zhao J, Zhang Z.   +7 more
europepmc   +1 more source

Flexure Testing of Compacted Rectangular Beams

Journal of Pharmacy and Pharmacology, 1982
Melanie S Church, J W Kennerley
openaire   +1 more source

Experimental and Numerical Thermo‐Mechanical Characterization of Polylactic Acid Fabricated by Fused Filament Fabrication

Polymer Engineering &Science, EarlyView.
Experimental and numerical framework for characterizing the thermomechanical response of polylactic acid fabricated by fused filament fabrication. ABSTRACT This study investigates the thermomechanical response of polylactic acid (PLA) specimens fabricated by fused filament fabrication (FFF) at two nozzle temperatures (190°C and 230°C), while mechanical
B. Hanželič, B. Nečemer, S. Glodež, G. Harih   +3 more
wiley   +1 more source

Influence of Architected Core Topology on the Dynamic and Flexural Behaviour of Multi-Material Sandwich Structures. [PDF]

Polymers (Basel)
Doğanay Katı H, Khan M.
europepmc   +1 more source