Results 221 to 230 of about 15,733,928 (351)

Mechanical Properties of Carbon Fiber and Polyimide Fiber Hybrid Reinforced Polyimide Resin Matrix Composites at Room and High Temperatures. [PDF]

Polymers (Basel)
Lu N, Gao H, Gu Y, Dou H, Li Y.
europepmc   +1 more source

From Growing Conditions to Composite Performance: Acid‐Engineered Algerian Sisal Fibers for Sustainable Bio‐Epoxy Composites

Polymer Composites, EarlyView.
High‐Performance Sustainable Ski Core Bio‐Composite Derived from Bio‐Epoxy and Sisal Sibers Systems. ABSTRACT In pursuit of sustainable and high‐performance materials, this work investigates the potential of Algerian sisal fibers as renewable reinforcements in bio‐epoxy composites.
M. A. Kacem, R. Halimi, O. Duncan, T. Allen, M. Bodaghi   +4 more
wiley   +1 more source

Evaluating the Effect of Glass and Carbon Fiber Mesh on 3D-Printed Concrete Performance. [PDF]

Materials (Basel)
Janghorban E, Joshi A, Gaspar FJM.
europepmc   +1 more source

Development of Cost‐Effective and Highly Transparent Melamine Formaldehyde Resin Modified With Sodium Chloride for Enhancing Glossiness and Abrasion Resistance of Melamine Impregnated Paper

Polymer Engineering &Science, EarlyView.
An eco‐friendly melamine‐formaldehyde was produced by the addition of sodium chloride as a modifier. Modified MF resin improved surface gloss and abrasion resistance of decorative paper and decreased the formaldehyde emission. Curing time of the MF resin decreased with the addition of sodium chloride.
Saeed Kamrani, Antonio Pizzi, Peyman Ahmadi, Nadir Ayrilmis, Ali Dorieh, Adam Sikora, Štěpán Hýsek, Kateřina Hájková, Meysam Mehdinia   +8 more
wiley   +1 more source

The Effect of Ultraviolet Modification on the Performance of Polyamide Fiber-Reinforced Cement Mortars: Optimization and Characterization Using Response Surface Methodology. [PDF]

Polymers (Basel)
Akarsu Özenç A, Mardani A, Özenç F, Eren S.   +3 more
europepmc   +1 more source

Investigation of Crystal Structure Change and Mechanical Properties of 3D Printed PLA After Annealing

Polymer Engineering &Science, EarlyView.
Thermal annealing of FDM‐printed PLA significantly enhances longitudinal tensile and flexural strengths by increasing crystallinity to 46.6%. However, transverse properties remain constrained by weak interlayer adhesion, providing crucial insights into the anisotropic thermo‐mechanical behavior of printed biopolymers for demanding engineering ...
Huseyin Erdem Yalkin, Ayse Nur Ozkan
wiley   +1 more source

Effect of Two Post-Curing Units on the Physico-Mechanical Properties of 3D-Printed Resins for Permanent Crown Fabrication. [PDF]

Materials (Basel)
Mujayridi M, Matinlinna J, Silikas N.
europepmc   +1 more source

Comparing the Applicability of State‐Of‐The‐Art Photopolymer Injection Molds Printed by Multi‐Material Jetting and High‐Performance Digital Light Processing

Polymer Engineering &Science, EarlyView.
The workflow of comparing state‐of‐the‐art photopolymers in rapid tooling. ABSTRACT Additive manufacturing (AM) introduced the concept of layer‐by‐layer manufacturing, which allows the fast and direct production of parts. Additive technologies are also hybridized with conventional polymer processing technologies.
Szabolcs Krizsma, András Suplicz
wiley   +1 more source

Strength performance of hexagonal, hollow, and perforated GFRP-Reinforced concrete units: experimental, numerical, and AI-based investigations. [PDF]

Sci Rep
Mirdarsoltany M, Khodadadi N, Nanni A.
europepmc   +1 more source

Flexure Testing of Compacted Rectangular Beams

Journal of Pharmacy and Pharmacology, 1982
Melanie S Church, J W Kennerley
openaire   +1 more source