Results 241 to 250 of about 15,733,928 (351)

High‐strength composites by thiocracking of high‐polypropylene‐content mixed waste

Polymer International, EarlyView.
Mixed plastic waste made up of polystyrene and polypropylene was reacted with elemental sulfur to give high‐strength composites. Abstract Mixed‐material municipal waste poses a persistent end‐of‐life management challenge because the heterogeneous composition limits efficient separation and recycling. After disposal, mixed‐material waste often fragments
Athira Babu, Rhett C. Smith
wiley   +1 more source

Comparative Analysis of Physical and Mechanical Properties of Acrylic Resins for Interim Fixed Prostheses Under Thermocycling Aging. [PDF]

Bioengineering (Basel)
da Silva EVF, Ortiz CLE, Gomes MS, Condor WJAB, Santos KF, Bezerra SJC, Cesar PF, Bastos-Bitencourt NA, Bitencourt SB, Léon BLT.   +9 more
europepmc   +1 more source

Investigation of the Mechanical, Thermal, and Morphological Properties of ABS Composite Reinforced With Bentonite and DEHPA‐Modified Bentonite

Journal of Polymer Science, Volume 63, Issue 6, Page 1505-1517, 15 March 2025.
Mechanical and thermal properties of ABS/Bentonite/DEHPA composites. ABSTRACT This study investigates the mechanical, thermal, and surface characteristics of acrylonitrile–butadiene–styrene (ABS) composites reinforced with bentonite and bis(2‐ethylhexyl) phosphate (DEHPA)‐modified bentonite.
İdris Karagöz, B. Şebnem Şimşiroğlu, Elif Nur Özer, Harun Sepetcioglu, Jülide Hızal   +4 more
wiley   +1 more source

From Design to Acceptance: A Full-Scale Analysis of Prestressed Concrete Railway Sleepers According to EN 13230. [PDF]

Materials (Basel)
Chudyba Ł, Derkowski W, Lisowicz T, Ślaga Ł, Piech P.   +4 more
europepmc   +1 more source

In Situ Curing‐Enabled 3D Printing of Continuous Fiber‐Reinforced Thermosetting Composites

Journal of Polymer Science, EarlyView.
In situ curing‐enabled the 3D printing of continuous fiber/thermoset composites, which were reviewed. Particularly, four types of in situ curing, were discussed, including Radiation‐induced curing, photothermal curing, electrothermal curing, and frontal polymerization. AI‐integrated printing was also analyzed.
Xiaofei Wu, Harrison Hayworth, Shiren Wang   +2 more
wiley   +1 more source

Effect of calcium carbonate precipitate derived from sugar beet industry on the properties of poly (vinyl chloride) compounds. [PDF]

Sci Rep
Abdelhamed M, Sadik WAA, El-Demerdash AM, El-Rafey E.   +3 more
europepmc   +1 more source

Sustainable Polymer Biocomposites for Food Packaging: Green Nanotechnology, Circular Plastic Upcycling and Smart Functional Materials

Packaging Technology and Science, EarlyView.
Graphical abstract showing the development of biodegradable polymer biocomposites reinforced with natural fibres, green nanoparticles and waste‐plastic upcycling pathways toward sustainable smart food packaging materials ABSTRACT The fundamental hypothesis behind this review is that the combination of biodegradable polymer‐based biocomposites, which ...
Chandra Sekhar Espenti, Jaewoong Lee
wiley   +1 more source

An <i>in vitro</i> comparative study on the flexural strength of different restorative materials. [PDF]

Bioinformation
S K MR, Dutt P, Sharma K, Gill S, Gohil J, Bhalerao VU, Surana P.   +6 more
europepmc   +1 more source

Sustainable Utilization and Fire Protection of Wood‐Based Composites in Buildings: Innovations, Challenges, and Future Directions

Sustainable Development, EarlyView.
ABSTRACT The increasing use of wood and wood‐based composites in construction reflects a global shift toward renewable materials that support sustainable development objectives, including carbon reduction and responsible resource use. While wood offers substantial environmental benefits compared to conventional materials such as concrete and steel, its
Qaisar Munir, Marko Hyvärinen, Timo Kärki   +2 more
wiley   +1 more source

Influence of Printing Orientation and Ageing on Mechanical Properties of 3D-Printed Resins for Occlusal Splints. [PDF]

Materials (Basel)
Bosoni C, Vichi A, Franchi L, Al-Johani H, Goracci C.   +4 more
europepmc   +1 more source