Results 271 to 280 of about 129,728 (312)

Prototype of Compact Flexural Fatigue Testing Machine

Applied Mechanics and Materials, 2014
The purpose of this project is to build a prototype of compact flexural fatigue testing machine and to strive for an easy working-environment as required by the users besides cutting the cost of the machining. This particular project is about to build the prototype of compact flexural fatigue testing machine in compact mode.
Muhammad Azrie Husainy Mohd Jasri, Mohd Afendi, A.H.M. Fauzi   +2 more
openaire   +1 more source

Biaxial disc flexure – modulus and strength testing

British Ceramic Transactions, 1999
There is widespread use of biaxial testing of ceramics, but relatively little information concerning the accuracy of testing, and the pitfalls that can arise unless the test is carefully prescribed. The present paper reviews recent work in measuring elastic moduli using a biaxial natural frequency method, and in investigating some of the potential ...
R. Morrell, N.J. McCormick, J. Bevan, M. Lodeiro, J. Margetson   +4 more
openaire   +1 more source

Flexure Testing of Bent Hydraulic Tubing

2017
This recommended practice establishes a flexure test procedure for determining the fatigue strength of bent hydraulic tubing. The procedure is intended for conducting flexure fatigue testing of hydraulic and pneumatic tubing to determine the effects of tube fabrication methods, surface finishing, and other processing techniques on the fatigue ...
openaire   +1 more source

Flexural Testing of General Multi-Layered Composites

Journal of Composite Materials, 1991
Three-point bend tests were performed on two 32-layer balanced symmetric laminates. The advanced composite material is HI-TEX 46–8B carbon fibre in epoxy resin E7K8T, with a 59.5 % fibre volume fraction. A graphical technique based on classical beam theory was used to measure specimen longitudinal flexural and out-of-plane shear moduli. Likely sources
openaire   +1 more source

Flexure Fatigue Tests on Asphalt Paving Mixtures

1972
A repeated flexure apparatus which has been used for much of the recent research on fatigue behavior of asphalt paving was modified to accommodate 15-in.-long beam specimens with 3-in. instead of 1½-in. widths and depths. Controlled stress flexural fatigue studies were conducted for 10 different paving mixes using the larger cross section specimens in ...
BF Kallas, VP Puzinauskas
openaire   +1 more source

The Segmented Cylinder Flexural Strength Test

2008
Weiler showed in 1987 that the strength of ceramic heat exchanger tubes could be evaluated by flexural strength tests of cylindrical segments or longitudinal slices cut from the tubes. In the present study, a similar approach has been applied to measure the strength of short solid ceramic cylinders.
openaire   +1 more source

Biaxial Flexure Testing: Analysis and Experimental Results

1992
Characterization of the damage in ceramics after exposure to particulate environments involves measurements of the loss of mechanical strength when impacted by waterdrops, hail, and sand.1 The most desirable measure of strength degradation for particulate impacted specimens is a biaxial flexure test.
William F. Adler, Dennis J. Mihora
openaire   +1 more source

Flexural tests on trapezoidal steel sheets.

1993
XIV Congresso C.T.A., Viareggio, October ...
MAZZOLANI, FEDERICO MASSIMO, LANDOLFO R.
openaire   +1 more source

[Flexural strength tests of repaired amalgam specimen].

Deutsche zahnarztliche Zeitschrift, 1990
Test results of four types of alloys: Flexural strength declined significantly with increasing age of the specimen, however, differently for the tested alloys. The increase in mercury content of the repair amalgam did not influence flexural strength. The combination of materials with each other demonstrated that none of the amalgams was particularly ...
H G, Schaller, W, Götze, B, Kirn, A, Oehler   +3 more
openaire   +1 more source

Flexural Testing

2021
openaire   +1 more source