Results 111 to 120 of about 1,975,151 (297)
Advanced Electronic Materials, EarlyView.High‐conductive amorphous Pr0.7Ca0.3MnO3 (PCMO) is explored as an alternative to polycrystalline PCMO for memristive heterostructures with back‐end‐of‐line compatibility, targeting neuromorphic hardware integration. Structural, electrical, and band alignment analyzes are correlated with the electrical characterization of area‐dependent resistive ...
Max Buczek +12 more
wiley +1 more source
In‐Sensor Computing by Soft Threshold Logic Gates Under Different Humidity Conditions
Advanced Electronic Materials, EarlyView.Soft nanocomposite materials, based on gold cluster‐assembled thin films implanted in polydimethylsiloxane substrate, can perform reliable processing in ambient environmental conditions. Humidity influences the resistive switching and computational capabilities of the nanocomposites, that can be used as multifunctional material combining sensing ...
Giacomo Nadalini +2 more
wiley +1 more source
Extrinsic and Intrinsic Charge Transfer at Interfaces of Membrane‐Based Oxide Heterostructures
Advanced Electronic Materials, EarlyView.Freestanding oxides have emerged as a new opportunity to tailor oxides outside of the typical epitaxial constraints. We present the fabrication of TiO2‐terminated SrTiO3 membranes via direct growth control. We demonstrate competing ionic and electronic charge transfer in LaAlO3/SrTiO3 bilayers using near ambient pressure XPS.
Kapil Nayak +8 more
wiley +1 more source
Advanced Electronic Materials, EarlyView.Comparison of tunability efficiency between vacuum‐deposited PLD‐BTO films grown at Td = 550°C in the present study and representative previous reports. ABSTRACT Electrically tunable dielectric thin films are essential components for next‐generation low‐voltage electronic devices.
Shinya Kondo +7 more
wiley +1 more source
The paper considers the flue gas recirculation methods analysis and the implementation opportunities on heat only boilers with the installed heat capacity over 50MW.
Krickis, Otto
core
Porous Carbon Based Solid Adsorbents for Carbon Dioxide Capture [PDF]
, 2015 The aim of this project is the design, synthesis and characterisation of porous carbon structures capable of the selective capture of carbon dioxide (CO2) from the exhaust gases of coal and gas post-combustion power stations.
Travis, W
core
Artificial Intelligence for Fluorite Ferroelectric Materials: From Discovery to Optimization
Advanced Electronic Materials, EarlyView.Artificial intelligence accelerates the discovery and optimization of HfO2‐based fluorite ferroelectrics by linking synthesis, structure, properties, and device performance. Machine learning, deep‐learning analysis, and AI‐driven atomistic modeling enable predictive design, dopant screening, and closed‐loop optimization toward next‐generation ...
Faizan Ali +3 more
wiley +1 more source
Advanced ScienceThe rational design of precursor structure serves as a critical determinant for the pore geometry and gas separation performance of carbon molecular sieve (CMS) membranes.
Min Deng +13 more
doaj +1 more source
Anion‐Cation Synergistic Passivation for High‐Performance FA‐Cs Halide Perovskite Photodetectors
Advanced Electronic Materials, EarlyView.An anion‐cation synergistic passivation strategy is developed to improve perovskite photodetectors. Surface‐localized DMePDA2+ cations and bulk‐diffused Cl− anions simultaneously reduce defects, enhancing charge transport and suppressing recombination.
Hyeon‐Jong Shin +3 more
wiley +1 more source
Epitaxial Oxide Interfaces Create Poison‐Resistant CuO Sites for Environmental Catalysis
Angewandte Chemie, EarlyView.An epitaxially stabilized CuO overlayer on Ti1−xInxO2 creates electron‐poor, high‐symmetry Cu–O sites that activate interfacial lattice‐oxygen redox. This interface promotes NOx reduction through an Eley–Rideal pathway, diverts sulfate formation, and sustains CH3SH deep oxidation via a Mars–van Krevelen cycle, offering a route to poison‐resistant ...
Lupeng Han +14 more
wiley +2 more sources