Results 51 to 60 of about 755 (262)

Bed-To-Wall Heat Transfer in a Supercritical Circulating Fluidised Bed Boiler

Chemical and Process Engineering, 2014
The purpose of this work is to find a correlation for heat transfer to walls in a 1296 t/h supercritical circulating fluidised bed (CFB) boiler. The effect of bed-to-wall heat transfer coefficient in a long active heat transfer surface was discussed ...
Błaszczuk Artur, Nowak Wojciech, Jagodzik Szymon   +2 more
doaj   +1 more source

Conductive Additives for Next‐Generation Batteries: Emphasizing the Potential of Bio‐Derived 3D Carbon Architectures at Electrode–Electrolyte Interfaces

Advanced Materials Interfaces, EarlyView.
3D conductive frameworks can maintain continuous electron transport, mechanical stability, and interfacial integrity, helping next‐generation batteries operate more efficiently. This Review examines their relevance to Si anodes, all‐solid‐state batteries, and dry‐processed electrodes, and highlights bio‐derived carbons as sustainable, structurally ...
SeoYoung Ha, Inseo Ko, Jongyoung Choi, Weon Ho Shin, Sung Cik Mun, Jong Ho Won   +5 more
wiley   +1 more source

From the Discovery of the Giant Magnetocaloric Effect to the Development of High‐Power‐Density Systems

Advanced Materials Technologies, EarlyView.
The article overviews past and current efforts on caloric materials and systems, highlighting the contributions of Ames National Laboratory to the field. Solid‐state caloric heat pumping is an innovative method that can be implemented in a wide range of cooling and heating applications.
Agata Czernuszewicz, Yaroslav Mudryk, Jun Cui, Lucas Griffith, Duane D. Johnson, Julie Slaughter   +5 more
wiley   +1 more source

Fluidised Bed Gasification and Chemical Exergy Analysis of Pelletised Oil Palm Empty Fruit Bunches

Chemical Engineering Transactions, 2017
The National Biomass Strategy was envisioned to foster the efficient valorisation and management of Oil Palm Waste (OPW) in Malaysia. However, the proposed Circular Energy Economy is hampered by poor OPW fuel properties, inefficient conversion techniques,
B.B. Nyakuma, A. Ahmad, A. Johari, T.A.T. Abdullah, O. Oladokun, H. Alkali   +5 more
doaj   +1 more source

Overcoming Printing and Interfacial Challenges in Liquid Metal Direct Writing for Integrated Stretchable Electronics

Advanced Materials Technologies, EarlyView.
Liquid metal direct writing is advanced from a technological and fundamental point. Utilizing a kinematic bed, printing on large surfaces with irregularities is enabled. Furthermore, a pressure‐driven flow during printing is discovered that affects the thickness of traces.
Maximilian Krack, Lennert Purnal, Parth Vinayakrao Sewlikar, Sam Cuyvers, Gus Geurts, Rathul Nengminza Sangma, Derese Desta, Dieter Reenaers, Bart Ruttens, Iris De Graeve, Tom Hauffman, Seppe Terryn, Bram Vanderborght, Michaël Daenen, Wim Deferme, Monika Rai   +15 more
wiley   +1 more source

TREATMENT OF POME BY PILOT PLANT ANAEROBIC FLUIDISED BED REACTOR

International Islamic University Malaysia Engineering Journal, 2010
A pilot scale anaerobic fluidised bed reactor (AnFBR) of 2000 L capacity was studied to determine its performance to treat palm oil mill effluent (POME). The pilot plant was operated at ambient temperature with diluted POME as substrate.
Abdullah Al-Mamun, Azni Idris
doaj   +1 more source

End‐to‐End Sensing Systems for Breast Cancer: From Wearables for Early Detection to Lab‐Based Diagnosis Chips

Advanced Materials Technologies, EarlyView.
This review explores advances in wearable and lab‐on‐chip technologies for breast cancer detection. Covering tactile, thermal, ultrasound, microwave, electrical impedance tomography, electrochemical, microelectromechanical, and optical systems, it highlights innovations in flexible electronics, nanomaterials, and machine learning.
Neshika Wijewardhane, Lyn I. Jones, Richard M. Martin, Helen Winter, Faezeh Arab Hassani   +4 more
wiley   +1 more source

Particle Impact Breakage in Particulate Processing

KONA Powder and Particle Journal, 2014
The study of particle breakage in particulate processing is presented at two principal scales. Single-particle impact results are shown to be useful in deducing and understanding process-scale particle breakage ...
Agba Salman, Gavin Reynolds, Michael Hounslow   +2 more
doaj   +1 more source

Additive Manufacturing of Patient‐Specific Intracranial Aneurysm Cell Culture Models

Advanced Materials Technologies, EarlyView.
Patient‐specific intracranial aneurysm models were fabricated using chocolate moulding, 3D printed water‐soluble cores, and direct resin 3D printing. Moulding PDMS around sacrificial cores made of chocolate or 3D printed water‐soluble resin yielded accurate, expandable, and endothelializable models that outperformed resin‐based approaches.
Chloe M. de Nys, Jaimee‐Lee Wood, James I. Novak, Danilo Carluccio, Craig D. Winter, Ashley R. Murphy, Mark C. Allenby   +6 more
wiley   +1 more source

‘Surface functionalization of hight-strength aluminium powder with ceramic nanoparticles for additive manufacturing: influence of fluidised bed processing’

Journal of Materials Research and Technology
There is a limited number of metal alloys and metal-ceramic powders available for use in additive manufacturing (AM) processes. There is great demand to develop industrial-scale processes for producing raw material with the desired physicochemical ...
Neyder Sandoval, Sergio Sánchez-Delgado, Daniel Serrano, Sophia A. Tsipas   +3 more
doaj   +1 more source