Results 91 to 100 of about 2,063,722 (303)

Investigating the Effect of Inclination Angle and the Influence of Scan Parameters on the Appearance and Thermal and Mechanical Properties of Filigree Tension Rods of LPBF‐Manufactured NiTi Shape‐Memory Alloys

open access: yesAdvanced Engineering Materials, EarlyView.
This article investigates the dependence of the properties on the manufacturing orientation in the form of the inclination angle to the build plate of LPBF‐fabricated NiTi rods with a diameter of 150–220 µm. Metallographic, chemical, thermal, and mechanical characterization show behavior under identical manufacturing conditions that ranges from ...
Sandra Herzig   +2 more
wiley   +1 more source

Northeast Regional Meeting of the Kansas Food Safety Task Force, Olathe, Kansas, August 28, 2017.

open access: yes, 2017
PowerPoint presentation given at the 2015 Northeast Regional Meeting."The Kansas Food Safety Task Force was developed for food and feed safety and defense professionals to achieve prevention, intervention and response including the early detection ...
Kansas Food Safety Task Force.
core   +1 more source

Enhancement of the Through‐Thickness Electrical Conductivity of Carbon‐Fiber‐Reinforced Plastics Using Large Graphite Particles

open access: yesAdvanced Engineering Materials, EarlyView.
To enhance through‐thickness conductivity without sacrificing impregnation, large spherical graphite particles are intentionally employed in a low‐viscosity resin. Unlike finer conductive fillers, these particles remain outside the fiber bundles and accumulate in resin‐rich interlaminar regions during molding.
Keito Hosoe   +6 more
wiley   +1 more source

3D‐Printed Titanium Gyroid Scaffold Structure Integrated With Tough Hybrid Materials for Cartilage Replacement

open access: yesAdvanced Engineering Materials, EarlyView.
This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin   +12 more
wiley   +1 more source

New Stator Tooth for Reducing Torque Ripple in Outer Rotor Permanent Magnet Machine

open access: yesAdvances in Electrical and Computer Engineering, 2016
Torque ripple has been a major problem for the permanent magnet (PM) machine. It is discussed focusing on the magnetic circuit of the PM machine. Since it is known the relationship between the torque ripple and the magnetic energy that is stored in the
OZOGLU, Y.
doaj   +1 more source

Impact of the Process Atmosphere During Hot Isostatic Pressing on the Near‐Surface Composition of an Additively Manufactured Austenitic High‐Interstitial Steel

open access: yesAdvanced Engineering Materials, EarlyView.
A high interstital austenitic steel is additively manufactured and postdensified by HIP to eliminate gas porosity. Thereby, the loss of N and Mn in Ar HIP atmosphere is investigated. Further, HIP using N2 atmosphere is investigated which led to excessive nitride formation.
F. Großwendt   +4 more
wiley   +1 more source

Adaptive Robust Precision Motion Control of Linear Motors with Ripple Force Compensations: Theory and Experiments i

open access: yes, 2008
This paper studies the high performance robust motion con-trol of linear motors which are subjected to significant force ripple. Based on the structural property of linear motors, some simple models with unknown weights are used to ap-proximate the force

core  

Electrodeposition in Structural Lattices of Variable Architectures

open access: yesAdvanced Engineering Materials, EarlyView.
Electrodeposition enables geometry‐sensitive, autonomous void filling while simultaneously tuning chemical and mechanical properties. The development of approaches that can autonomously fill and heal material voids and yield composites with tailorable properties is increasingly relevant in engineering.
Yeong‐Man Kwon   +3 more
wiley   +1 more source

Development of a Cold Wall Reactor System for the Low‐Pressure Chemical Vapor Deposition of BN on SiC Fiber Tow

open access: yesAdvanced Engineering Materials, EarlyView.
A cold wall reactor is developed to coat a SiC fiber tow with BN by low pressure chemical vapor deposition. The precursor gas is triethylamine borane mixed with ammonia. The heating process induces a temperature gradient, with the temperature decreasing from the core to the surface of the multifilament tow.
Pierre Fenetaud, Sylvain Jacques
wiley   +1 more source

Casimir Force from VEQF Ripple Dynamics

open access: yes
The Vacuum Energy Quanta Field (VEQF) framework models the Casimir force as a consequence of transactional ripple suppression between conducting plates, arising from boundary constraints on the VEQF lattice, rather than virtual particle fluctuations or zero-point energy.
openaire   +1 more source

Home - About - Disclaimer - Privacy