Results 81 to 90 of about 5,212 (262)

New Stator Tooth for Reducing Torque Ripple in Outer Rotor Permanent Magnet Machine

Advances in Electrical and Computer Engineering, 2016
Torque ripple has been a major problem for the permanent magnet (PM) machine. It is discussed focusing on the magnetic circuit of the PM machine. Since it is known the relationship between the torque ripple and the magnetic energy that is stored in the
OZOGLU, Y.
doaj   +1 more source

Ontology‐Aligned Structuring and Reuse of Multimodal Materials Data and Workflows Toward Automatic Reproduction

Advanced Engineering Materials, EarlyView.
Reproduction of stacking fault energy calculations from literature with a semi‐automated large language model‐assisted extraction procedure: extraction of simulation protocol, atomistic structures, computational parameters, and reported results, ontology alignment, knowledge graph construction and, finally, recomputation forvalidation.
Sepideh Baghaee Ravari, Abril Azocar Guzman, Sarath Menon, Stefan Sandfeld, Tilmann Hickel, Markus Stricker   +5 more
wiley   +1 more source

Symmetry‐Guided Multifunctional Acoustic System Based on Mechanically Actuated Sonic Crystals

Advanced Engineering Materials, EarlyView.
This study presents the design, simulation, and experimental validation of amultifunctional acoustic metamaterial based on rotationally engineered sonic crystals.By tuning cylinder orientations, controllable band gaps and six distinct functionalities—including switching, topological insulation, beam splitting, and logic operations—areachieved ...
Yuanyan Zhao, Sriram Subramanian, Gianluca Memoli   +2 more
wiley   +1 more source

Torque ripple suppression in non‐commutation interval of the coreless brushless DC motor based on unipolar PWM predictive control

IET Power Electronics
Aiming at the torque ripple caused by significant current ripple and non‐ideal back‐electromotive force (back‐EMF) of coreless brushless DC motor (BLDCM), an incremental predictive control strategy based on unipolar pulse width modulation (PWM) is ...
Chong Zeng, Zhongxin Wan, Song Huang, Jiao He   +3 more
doaj   +1 more source

Towards Smoother Linear Locomotion Through Combined Linear Machine Structural Optimization Methods

Energies
Permanent Magnet Linear Synchronous Motors (PMLSMs) are the dominant actuation solution for high-end manufacturing equipment, such as semiconductor lithography systems, owing to their superior force density and direct-drive capabilities.
Yiheng Chen, Zaixin Song, Yongtao Liang
doaj   +1 more source

Casimir Force from VEQF Ripple Dynamics

The Vacuum Energy Quanta Field (VEQF) framework models the Casimir force as a consequence of transactional ripple suppression between conducting plates, arising from boundary constraints on the VEQF lattice, rather than virtual particle fluctuations or zero-point energy.
openaire   +1 more source

Electrochemical Behavior of Flame‐Sprayed Sc‐Doped AlCoCrFeMo High‐Entropy Alloy Coatings in 3.5% Sodium Chloride Solution

Advanced Engineering Materials, EarlyView.
Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar, Akash Vyas, Mohammad Aatif Qazi, Nashit Jalal, Maria Ophelia Jarligo, Mostafa Yakout, Jing Liu, André McDonald   +7 more
wiley   +1 more source

Microstructure Reconstruction in Battery Electrodes Using Machine Learning Based on Low‐Voltage Focused Ion Beam–Scanning Electron Microscopy Tomography Images

Advanced Engineering Materials, EarlyView.
Low‐voltage FIB‐SEM tomography combined with a image preprocessing pipeline improves phase contrast and enables reliable machine‐learning segmentation of conductive networks in lithium‐ion battery electrodes. Structural descriptors are extracted from segmented images, done semimanually and automated, and compared.
Lisa Beran, Vincent Nebel, Dominik Perius, Kshitij Kumar, Yannis Heim, Laura Bies, Tobias Kraus   +6 more
wiley   +1 more source

Precipitation Simulations of the O‐Phase in Ti2AlNb Alloys Processed by Laser Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
Simulated and experimental evolution of the O‐phase volume fraction during postprocessing of a Ti‐21Al‐25Nb (at.%) alloy processed by laser powder bed fusion. With results of sensitivity to input parameters from a thorough and quantified analysis, the interfacial energy matrix/precipitate is the most relevant input parameter for the simulation of the O‐
Silvana Tumminello, Joachim Gussone, Suzana G. Fries, Marcus Rackel, Andreas Stark, Norbert Schell, Jan Haubrich, Guillermo Requena   +7 more
wiley   +1 more source

Modeling Dislocation Cutting of γ′ Precipitates in Ni‐Base Superalloys: Linking Atomistic and Dislocation Dynamics Simulations

Advanced Engineering Materials, EarlyView.
Dislocation cutting of γ′ precipitates in Ni‐based superalloys is investigated by linking atomistic simulations with discrete dislocation dynamics. The critical cutting stress is shown to be governed by the antiphase boundary energy, while line tension effects promote edge‐preferred cutting.
Frédéric Houllé, Siwen Gao, Marc Fivel, Anxin Ma, Daria Smirnova, Sriram Anand, Arun Prakash, Julien Guénolé, Alexander Hartmaier, Erik Bitzek   +9 more
wiley   +1 more source