Results 51 to 60 of about 99,528 (347)
Evaluating Energy Absorption Performance of Filled Lattice Structures
Advanced Engineering Materials, EarlyView.Maximum stress must be considered to robustly evaluate energy absorber designs. This approach was applied to compare all types of absorbers in a single Ashby diagram and determine the utility of filling lattice voids with a second material. High‐performance fillers can improve the performance of lattices that are limited by buckling or catastrophic ...
Christian Bonney +2 more
wiley +1 more source
Exact Model Reduction for Damped-Forced Nonlinear Beams: An Infinite-Dimensional Analysis
, 2017 We use invariant manifold results on Banach spaces to conclude the existence of spectral submanifolds (SSMs) in a class of nonlinear, externally forced beam oscillations. SSMs are the smoothest nonlinear extensions of spectral subspaces of the linearized
Haller, George, Kogelbauer, Florian
core +1 more source
Surface Tension Measurement of Ti‐6Al‐4V by Falling Droplet Method in Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.In this article, the temperature‐dependent surface tension of free falling, oscillating Ti‐6Al‐4V droplets is investigated in both argon and monosilane doped, oxygen‐free atmosphere. Droplet temperature and oscillation are captured with one single high‐speed camera, and the surface tension is calculated with Rayleigh's formula.
Johannes May +9 more
wiley +1 more source
Effects of mistuning on dynamic behavior of nonlinear cyclic systems with lump masses and cubic nonlinearity [PDF]
, 2016 Mistuning in cyclic symmetric systems increases severely the forced response of system and splits the modes. This paper concerns with nonlinear behavior of mistuned cyclic systems.
Estabragh, E. Raeisi +2 more
core +2 more sources
Advanced Engineering Materials, EarlyView.Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir +5 more
wiley +1 more source
Forces on oscillating uniform and tapered cylinders in a crossflow [PDF]
, 1998 Forces are measured at both ends of rigid cylinders with span 60 cm, performing transverse oscillations within an oncoming stream of water, at Reynolds number Re ~3800.
Hover, F. S. +2 more
core
An Experimental High‐Throughput Approach for the Screening of Hard Magnet Materials
Advanced Engineering Materials, EarlyView.An entire workflow for the high‐throughput characterization and analysis of compositionally graded magnetic films is presented. Characterization protocols, data management tools and data analysis approaches are illustrated with test case Sm(Fe, V)12 based films.
William Rigaut +16 more
wiley +1 more source
Longitudinal forced harmonic vibrations of vertical rods with concentrated mass.
Вестник Дагестанского государственного технического университета: Технические наукиObjective. Longitudinal forced harmonic vibrations of vertical rods with a concentrated mass at the end are considered.Method. The mathematical model of forced kinematically excited longitudinal vibrations is described by a differential equation and ...
H. P. Kulterbaev, M. M. Payzulaev
doaj +1 more source
Harmonic Analysis of the Wind-Loaded Bar Dome at the Satellite Services Centre in Psary
Archives of Civil Engineering, 2016 The research paper presents the results of the dynamic analysis of an existing bar dome subjected to wind loads. The calculation model of the structure was constructed using the finite element method. The dome was subjected to the standard wind pressure,
Szaniec W., Zielińska K.
doaj +1 more source
, 2018 In-plane wave propagation in a periodic rectangular grid beam structure, which includes rotational inertia (so-called 'Rayleigh beams'), is analyzed both with a Floquet-Bloch exact formulation for free oscillations and with a numerical treatment ...
Bigoni, D. +3 more
core +1 more source