Results 71 to 80 of about 2,714,278 (296)

Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy

Advanced Engineering Materials, EarlyView.
A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang, Aparajita Pramanik, Sandipan Sen, Shubhashis Dixit, Marcel Muench, R. J. Vikram, Daniel Schliephake, Yolita M. Eggeler, Ankur Chauhan, Martin Heilmaier, Alexander Kauffmann   +10 more
wiley   +1 more source

Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A

Advanced Engineering Materials, EarlyView.
The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han, Julian M. Rosalie, Jan Radners, Mauro Madia, Philipp von Hartrott, Birgit Skrotzki   +5 more
wiley   +1 more source

5.

, 1990
1
Proc. Fracture and
core  

Effect of Length and Diameter of Fiber Reinforced Composite Post on Fracture Resistance of Remaining Tooth Structure [PDF]

Journal of Dental Materials and Techniques, 2013
Introduction: Post and core has been considered for endodontically treated tooth, especially in cases with severe damage crowns. Recently fiber reinforced composite posts (FRC post) have been used in the treatment of endodontically treated teeth. Because
Saeid Ebrahimzadeh, Nafiseh Asadzadeh, Bijhan Heidari, Mahdiyeh Seifi   +3 more
doaj  

High‐Temperature Nanoindentation of Metals: Assessing Thermal Drift, Frame Compliance, and Chemical Composition Effects on the Reported Mechanical Properties

Advanced Engineering Materials, EarlyView.
Do not let thermal drift and instrument artifacts deceive high‐temperature nanoindentation results. We compare classical Oliver–Pharr and automatic image recognition analyses across steels and a Ni alloy to quantify these effects. Accounting for artifacts reveals systematic softening with temperature, while Cr and Ni additions boost resistance ...
Velislava Yonkova, Steffen Brinckmann, Ruth Schwaiger   +2 more
wiley   +1 more source

Creep Properties and Deformation Mechanism of Additively Manufactured NiAl‐CrMo Composites

Advanced Engineering Materials, EarlyView.
Additively manufactured NiAl‐CrMo composites contain numerous interfaces and cell boundaries that control their creep response. At 700°C under high applied stress, creep is dominated by dislocation‐controlled power‐law mechanisms. At 800°C–900°C and lower stresses, creep is primarily diffusion‐controlled along cell boundaries.
Jan Vollhüter, Andreas Bezold, Johan Westraadt, Katharina Fiegl, Subham Chattoraj, Benjamin Wahlmann, Carolin Körner, Michael Mills, Mathias Göken, Steffen Neumeier   +9 more
wiley   +1 more source

Modular Critical Element Recycling Platform Using a Nanoporous Additively Manufactured Gyroid

Advanced Engineering Materials, EarlyView.
A modular recycling platform integrates 3D‐printed nanoporous gyroid structures to enable efficient critical element recovery. This system utilizes a hierarchical architecture, combining macroscopic channels with polymerization‐induced nanoscale porosity. By systematically tuning structural wall thickness and resin formulation, the platform achieves an
Xiangyu Gao, Keldy Mason, Mert Gülçür, Rachel Paddock‐Lamb, Prince Alvin Fofanah, Zachariah A. Page, Michael Cullinan   +6 more
wiley   +1 more source

Influence of chlorides on the fracture toughness and fracture resistance under the mixed mode I/II of high-performance concrete

, 2020
This experimental study shows the conjunction of fracture mechanics with the ability of high-performance concrete (HPC) to resist an aggressive chloride environment. Moreover, the influence of a chloride-contaminated environment on the fracture toughness
Konečný, Petr, Lehner, Petr, Horňáková, Marie, Miarka, Petr, Seitl, Stanislav, Bílek, Vlastimil, Sucharda, Oldřich   +6 more
core   +1 more source

A Fracture Mechanics-based Method for Prediction of Cracking of Circular and Elliptical Concrete Rings under Restrained Shrinkage [PDF]

, 2014
This article has been made available through the Brunel Open Access Publishing Fund.A new experimental method, utilizing elliptical ring specimens, is developed for assessing the likelihood of cracking and cracking age of concrete subject to restrained ...
Dong, W, Wu, Z, Zhou, X, Zhou, Xiangming, Dong, Wei, Wu, Zhimin   +5 more
core   +1 more source

Fracture analysis of debonding mechanism for FRP plates [PDF]

, 2009
Inevitable flaws in the concrete-FRP interface govern plate debonding, and are not amenable to finite element analysis because the models require far more detail than will ever be available for the interface. This thesis describes a global-energy-balance
Achintha, Paththini Marakkala Mithila
core   +3 more sources