Results 41 to 50 of about 29,365 (262)
Journal of Marine Science and Engineering, 2022 Welding is used as the main joining method in various industries, including the shipbuilding industry. In the case of welded structures, structural integrity assessment is essential to ensure the safety of the structure because many defects inevitably ...
Jihoon Kim +2 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar +7 more
wiley +1 more source
Comparison of Testing Method Effects on Cracking Resistance of Asphalt Concrete Mixtures
Applied Sciences, 2021 As an inherent characteristic of materials, the fracture toughness is an important parameter to study the cracking behavior of asphalt concrete mixtures.
Dayong Yang +2 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal +3 more
wiley +1 more source
Applied SciencesThe translaminar fracture toughness of pultruded Glass Fiber Reinforced Polymers (GFRP) is influenced by several factors, including the type of matrix, fiber, the fiber volume ratio, the proportion of plies at each angle and the size of the test ...
Zenghui Zhao +3 more
doaj +1 more source
The effect of TiN inclusions on the fracture mechanism of 20CrMnTi steel with lath martensite
Materials Research Express, 2020 This study aims to investigate the effect of TiN inclusions on the fracture mechanism of 20CrMnTi steel with martensite. Size of martensite packets, blocks and TiN inclusions were characterized, and the room-temperature tensile properties, impact ...
Yong Zhu +3 more
doaj +1 more source
Fracture toughness of locust cuticle [PDF]
Journal of Experimental Biology, 2012 SUMMARYInsect cuticle is one of the most common biological materials, yet very little is known about its mechanical properties. Many parts of the insect exoskeleton, such as the jumping legs of locusts, have to withstand high and repeated loading without failure.
Jan-Henning, Dirks, David, Taylor
openaire +2 more sources
Additive Manufacturing of Alumina‐Reinforced Elastomers
Advanced Engineering Materials, EarlyView.Vat‐photopolymerized elastomers reinforced with platelet‐shaped alumina exhibited preferential orientation, reduced porosity, and significantly enhanced mechanical performance. A 3 wt% platelet loading increased tensile strength from 12.4 to 45.7 MPa, highlighting the critical role of filler morphology in elastomeric VPP composites.
Majid Barzegar Keyvani +6 more
wiley +1 more source
Mezzo-scopic Analysis of Fracture Toughness in Steels
Materials Research, 2002 The cleavage fracture toughness of steels was mezzo-scopically analyzed on the basis of the statistical local fracture criterion approach. The statistical stress criterion at the crack tip region suggests that the cleavage fracture toughness in steels ...
Miyata Takashi, Tagawa Tetsuya
doaj
Effect of Aging on Fracture Toughness of Al6061-Graphite Particulate Composites [PDF]
Mechanics of Advanced Composite Structures, 2019 This article presents the investigative work conducted on the fracture toughness and microstructure of Al6061-9% graphite particulate composites. The requisite specimens for the fracture toughness testing were compact tension ones prepared using stir ...
Saleemsab Doddamani +1 more
doaj +1 more source