Results 91 to 100 of about 4,036,679 (293)
AIP Advances, 2018 Lateral force microscopy (LFM) is an established technique to assess friction forces at the nanoscale. Nanoindentation followed by unidirectional sliding (NUS) is also used to evaluate friction forces at the micro/nanoscale.
F. G. Echeverrigaray +8 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Functionally graded metal–ceramic femoral stems are engineered through continuous UMAT‐based stiffness tailoring, eliminating discrete material interfaces while enhancing biomechanical compatibility. Low‐index power‐law gradation optimizes load transfer, reduces stress shielding, and controls implant–bone micromotion, highlighting a materials‐design ...
Rihem Nouira, Sameh Elleuch, Hanen Jrad
wiley +1 more source
High-temperature wear performance and mechanism of NM400/NM500 mining machinery steels
工程科学学报, 2019 The friction and wear behavior of NM400 and NM500 steels in the temperature range from room temperature to 300℃ were investigated, including the formation of interface oxide, wear surface morphology, and microstructures.
HUANG Xia-xu +3 more
doaj +1 more source
Additive Manufacturing of Alumina‐Reinforced Elastomers
Advanced Engineering Materials, EarlyView.Vat‐photopolymerized elastomers reinforced with platelet‐shaped alumina exhibited preferential orientation, reduced porosity, and significantly enhanced mechanical performance. A 3 wt% platelet loading increased tensile strength from 12.4 to 45.7 MPa, highlighting the critical role of filler morphology in elastomeric VPP composites.
Majid Barzegar Keyvani +6 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees +6 more
wiley +1 more source
Demo 03-02 Static vs. Sliding Friction
, 2001 This demonstration shows that the coefficient of static friction is greater than the coefficient of dynamic or sliding friction for the same two surfaces.
core
Advanced Engineering Materials, EarlyView.This study explores the discrepancies between bulk mechanics and spatial mapping in a tissue‐mimetic hydrogel model. Microplastic particles create localized stiff mechanical microenvironments that are detectable by cellular‐scale nanoindentation but leave bulk properties unchanged as measured by rheology.
Ahron T. Verschleisser +3 more
wiley +1 more source
Entropy‐Driven Design of Low‐Melting‐Point Alloys via Compositionally Complex Strategy
Advanced Engineering Materials, EarlyView.Conventional low‐melting‐point alloys (LMPAs) are limited by a narrow compositional space and inherent property trade‐offs. This review presents an entropy‐driven design strategy that overcomes these limitations, ushering in a new class of low‐melting‐point compositionally complex alloys (LMCCAs).
Yinghui Shang +6 more
wiley +1 more source
Tribology Online, 2012 In this research, dynamic friction behavior of paper-based wet friction material subjected to contact pressure fluctuation was investigated experimentally and theoretically. Complex friction coefficient obtained by the ratio between dynamic components of
Yasuhisa Hattori, Yusuke Kato
doaj +1 more source
Advanced Engineering Materials, EarlyView.CT‐based finite element simulations combined with in situ X‐ray computed tomography are used to analyze insert pull‐out in nickel‐coated polymer foams. Despite variations in material parameters, deformation consistently concentrates within a narrow annular region around the insert.
Yannik Bautz +4 more
wiley +1 more source