Results 81 to 90 of about 70,183 (217)

A Dislocation Perspective on Strength and Toughness in Ceramics

Advanced Engineering Materials, EarlyView.
Dislocations in ceramics enjoy a long but yet under‐appreciated history. The three research waves for dislocations in ceramics highlight the topic evolution over the last 90 years. This review focuses on the impact of dislocation on strength and toughness in ceramics.
Xufei Fang
wiley   +1 more source

Influence of Si Content and Milling Duration on the Microstructure and Mechanical–Tribological Properties of AlCoCrFeNiSi High‐Entropy Alloys

Advanced Engineering Materials, EarlyView.
Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş, Mehmet Emin Demir, Sercan Özpınar   +2 more
wiley   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Design and Analysis of Compression–Torsion Coupling Metamaterials Using the Golden Section Method

Advanced Engineering Materials, EarlyView.
A novel compression–torsion metamaterial is engineered using inclined rods and symmetry breaking. To optimize its torsional performance, the golden section method is employed. The mechanical response of the metamaterial is validated through both numerical analysis and experimental validation.
Amirhossein Hassani, Sara Bagherifard
wiley   +1 more source

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source

Stretching the Printability Metric in Direct‐Ink Writing with Highly Extensible Yield‐Stress Fluids

Advanced Functional Materials, EarlyView.
This study introduces “drawability” as a new metric for assessing printability in direct‐ink writing, focusing on gap‐spanning performance and speed robustness. By designing yield‐stress fluids with high extensibility, we demonstrate that extensional strain‐to‐break significantly enhances printability.
Chaimongkol Saengow, Samya Sen, Joaquin Yus, Eliza E. Lovrich, Amanda G. Hoika, Kelly M. Chang, Arielle A. Pfeil, Nellie Haug, Amy J. Wagoner Johnson, Randy H. Ewoldt   +9 more
wiley   +1 more source

Transfer Printing and Reconfiguration of Soft Electronics Using Digital Microfluidics and Laser Machining

Advanced Functional Materials, EarlyView.
This paper presents a digital microfluidics‐based technique for transferring and reconfiguring soft nanomembranes. Laser‐machined nanothin membranes are picked up, transported, and aligned via tailored surface tension and the actuation of water droplets, enabling the development of flexible electronics, the integration of functional materials on 3D ...
Quang Anh Nguyen, Chi Cong Nguyen, Tran Bach Dang, Phuoc Thien Phan, Jordan Thorpe, Michael Listyawan, Nhat Minh Doan, Sinuo Zhao, Hongru Chen, Trung Thien Hoang, Mingsheng Xu, Jisheng Han, Thanh Nho Do, Adam Hill, Timothée Mouterde, Hoang‐Phuong Phan   +15 more
wiley   +1 more source

Study on the influence of hard tri-body particles on friction noise of brake systems

Jixie qiangdu
To investigate the effect of three-body particle invasion on the friction noise of friction pairs, a friction testing machine for the test research was constructed.
DING Yining, YAN Xiaoyu, CHEN Bingsan, SUN Haobin, YANG Minghan, ZHENG Yuhuang   +5 more
doaj  

Pickering‐Engineered Microparticles for Magnetically Guided Motion and Light‐Triggered Catalysis

Advanced Functional Materials, EarlyView.
Magnetically responsive wax microparticles stabilized by hematite cubes through the Pickering emulsification strategy are developed, showing controlled size, motion, and light‐activated catalytic activity. Annealing under a magnetic field enhances their mobility and steering.
Chiara Ferlito, Ludovico Guercio, Giuseppe Cavallaro, Giuseppe Lazzara, Theodore Hueckel, Lorenzo Lisuzzo, Stefano Sacanna   +6 more
wiley   +1 more source

Transparent and Robust LiCl–Organohydrogel Triboelectric Nanogenerator With Deep Learning Assisted Sensing

Advanced Functional Materials, EarlyView.
Develop a LiCl–PEI–PAM hydrogel with 3000% stretchability and excellent optical transparency. Through comparative studies of various salts, confirm that LiCl is the most suitable salt for high TENG output. Achieve excellent freeze‐resistant, dry‐resistant, and rapid self‐healing (10 s) properties even in extreme environments. Balance ionic conductivity,
Hai Anh Thi Le, Thien Trung Luu, Duc‐Manh Dinh, Kyehan Rhee, Kyungwho Choi, Dukhyun Choi, Yong Tae Park   +6 more
wiley   +1 more source