Results 131 to 140 of about 17,765 (271)

Effect of Heat Treatment on the Microstructure and Properties of Ti600/TC18 Joints by Inertia Friction Welding. [PDF]

Materials (Basel), 2022
Liu Y, Ren K, Tian W, Shangguan X, Tan S, Yang Q.   +5 more
europepmc   +1 more source

Advances in friction stir welding of steel : Project HILDA

, 2014
A microstructure and property evaluation of friction stir welded DH36 6mm plate has been undertaken. The study examined a wide range of process parameters and, from this, a process parameter envelope has been developed and an initial process parameter ...
Cater, Stephen R., Camilleri, Duncan, Poletz, Nicolas, Arbaoui, Larbi, Toumpis, Athanasios, Galloway, Alexander, Micallef, Daniel   +6 more
core  

Feasibility and optimization of dissimilar laser welding components [PDF]

, 2008
Demands placed on dissimilar metals joints have increased from various viewpoints, such as, environmental concerns, energy saving, high performance, cost saving and so on.
Hassan, Ezzeddin Mohamed
core  

Comparing the In‐Plane Shear Behavior of Glass Fiber‐Reinforced and Carbon Fiber‐Reinforced Polymer Laminates With the Same Epoxy Matrix System in ±45° Tensile Tests

Polymer Composites, Volume 47, Issue 12, Page 11051-11068, 20 June 2026.
Schematic illustration of ±45° tensile testing, including detection of first‐ply failure (FPF) by optical crack detection and acoustic emission monitoring, comparison of FPF values with ASTM D3518 and D3039 criteria, and resulting ply level stress states at FPF for GF‐ and CF‐epoxy laminates.
Maria Gfrerrer, Vasco D. C. Pires, Andreas J. Brunner, Clara Schuecker, Gerald Pinter   +4 more
wiley   +1 more source

Study on Residual Stress and Optimization of Welding Parameters in Linear Friction Welding of TC17 Titanium Alloy. [PDF]

Materials (Basel), 2022
Gong H, Liu M, Zhang T, He Y, Wu Y, Yu Z.   +5 more
europepmc   +1 more source

Arc welding of high strength aluminium alloys for armour systems applications [PDF]

, 2011
The ternary Al-Cu-Mg system 2xxx series aluminium alloys were examined as construction materials for armour system applications based upon comparable ballistic properties to the currently employed Al-7xxx series alloys.
Pickin, Craig Graeme
core  

The Firebrands Echo: National Fantasy as an Obstacle to Jean‐Luc Mélenchon's Populist Spectacle

Constellations, EarlyView.
Reid A. Kleinberg
wiley   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, Volume 28, Issue 12, 17 June 2026.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

A New Method of Predicting the Parameters of the Rotational Friction Welding Process Based on the Determination of the Frictional Heat Transfer in Ti Grade 2/AA 5005 Joints. [PDF]

Materials (Basel), 2023
Lacki P, Adamus J, Więckowski W, Motyka M.   +3 more
europepmc   +1 more source

Welding defects at friction stir welding

Metalurgija, 2015
The paper presents an overview of different types of defects at friction stir welding. In order to explain the reasons for their occurrence a short theoretical background of the process is given first. The main emphasis is on the parameters that influence the process. An energy supply based division of defects into three disjoint groups was used.
P. Podržaj, B. Jerman, D. Klobčar
openaire   +3 more sources