Results 161 to 170 of about 88,766 (300)

Three-dimensional analytical model for residual stress in the weld of thick plates by friction stir welding [PDF]

, 2023
Haidong Yu, Chang Gao, Ke Yuan, Wei Chen
openalex   +1 more source

The Culture Clash of AI Adoption in Lean Quality Management. Resolving the Tensions at Siemens Electronics Works Amberg

Information Systems Journal, Volume 36, Issue 3, Page 315-339, May 2026.
ABSTRACT Artificial intelligence (AI) brings great potential for manufacturers, but clashes with the established culture due to the unexplainable and opaque nature of the solutions it provides. Having little experience in AI and machine learning (ML), most manufacturing leaders experience barriers implementing AI.
Benjamin van Giffen, Gunter Beitinger, Helmuth Ludwig, Bill Schiano, Konstantin Schmidt, Jan vom Brocke   +5 more
wiley   +1 more source

Friction Welding

Journal of the Japan Welding Society, 1967
Atsushi Hasui, Sadao Fukushima, Junichi Kinugawa   +2 more
openaire   +2 more sources

Parametrical Analysis of Friction Stir Welding of Dissimilar Aluminum AA7075 and AA2024 Using Graph Labeling

, 2012
J. Jayapriya, D. Muruganandam, K. Thirusangu, Sushil Lal Das   +3 more
openalex   +2 more sources

Properties and Tempering Stability of Friction-welded Joints of 700-MPa-grade Fine-grained Steel [PDF]

, 2019
Runchang Liu, Cheng Yang, Yuwei Sun, Long Zhi Zhao   +3 more
openalex   +1 more source

Strain Development During Cure of Partially Pre‐Cured Thermosetting Composites Measured With Distributed Fiber Optic Sensors

Polymer Composites, Volume 47, Issue 8, Page 7155-7169, 20 April 2026.
Schematic representation of the beneficial effect of ply pre‐curing on temperature overshoot, internal strain and warpage during cure of thin and thick thermosetting composites. ABSTRACT Detection of manufacturing‐induced defects in thermosetting composites is crucial to guarantee part quality, safety, and improve manufacturing efficiency.
Francesco Taddei, Giacomo Struzziero, Valentin Ott, Véronique Michaud   +3 more
wiley   +1 more source

Studi Eksperimen Pengaruh Variasi Kecepatan Putar terhadap Temperatur dan Tensile Strength pada Friction Welding dengan Material High Density Polyethylene

, 2017
Miftahul Ahzabuddin, Yusuf Kaelani
openalex   +2 more sources

Accelerated Mechanochemical Depolymerization of Poly(styrene) Due To Formation of a Cohesive State

ChemSusChem, Volume 19, Issue 7, 14 April 2026.
A highly reactive, continuous state of poly(styrene) (PS) was discovered to aid its mechanochemical depolymerization, which is (a) more reactive than PS powder, (b) insensitive to effects of oxygen, (c) driven by shear rather than compressive stresses, and (d) sensitive to PS loading.
Yuchen Chang, Aubrey M. Hepstall, Adrian H. Hergesell, Claire L. Seitzinger, Pawel Chmielniak, Ina Vollmer, Carsten Sievers   +6 more
wiley   +1 more source

Laser Metal Deposition of Aluminum Alloys 7075 and 5083 with the Addition of Volatile Alloying Elements through Powder Blending

Advanced Engineering Materials, Volume 28, Issue 7, 8 April 2026.
This study investigates laser metal deposition of aluminum alloys EN AW‐7075 and EN AW‐5083, using powder blending to compensate zinc and magnesium evaporation. In situ alloying and ex situ alloying with ZnAl12 and AZ91 preserve near‐standard compositions and improve mechanical properties.
Finn Bendixen, Anastasiya Toenjes, Annika Bohlen, Thomas Seefeld   +3 more
wiley   +1 more source

Friction stir welding

Materials Today, 2010
Daniela Lohwasser, Zhan Chen
  +6 more sources