Results 51 to 60 of about 225,313 (249)

Characterization of Nitinol Produced by Laser Powder Bed Fusion for Mechanical Metamaterial Applications

Advanced Engineering Materials, EarlyView.
Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek, Jakub Hurník, Miroslav Šmíd, Ondřej Zobač, Melanie Todt, Daniel Koutný   +5 more
wiley   +1 more source

Composition‐Tuned Enhancement of the Anomalous Nernst Effect in FeCo–Pt Thin Films on Rigid and Flexible Substrates

Advanced Engineering Materials, EarlyView.
Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi, Hiroyuki Awano, Kenji Tanabe   +2 more
wiley   +1 more source

Multifunctional Crushing and Piezoresistive Self‐Sensing in Conductive Epoxy/CNT‐Coated Polyetherimide TPMS Lattices

Advanced Engineering Materials, EarlyView.
This study reports lightweight polyetherimide triply periodic minimal surfaces lattices coated with carbon nanotube‐reinforced epoxy that combine mechanical robustness with self‐sensing. The conformal coating enhances stiffness, strength and energy absorption while enabling reliable strain monitoring.
A. Triay, J. Schneider, P. Harrison, S. Kumar   +3 more
wiley   +1 more source

Generalized topological spaces with associating function

, 2019
Generalized topological spaces in the sense of Császár have two main features which distinguish them from typical topologies. First, these families of subsets are not closed under intersections. Second, we allow for the possibility that the whole space is not open. Hence, some points of the universe may be beyond any open set.
openaire   +2 more sources

Solid‐State Diffusion and Intermetallic Phase Formation in Roll‐Bonded Mg–Zn Composites With Kirigami‐Patterned Inlay

Advanced Engineering Materials, EarlyView.
Mg–Zn composites with a thickness of 0.21 mm were fabricated using roll bonding of a kirigami‐patterned Mg alloy inlay within a Zn matrix. Thermal activation following this process led to the formation of tailored intermetallic structures, which provided the composite with enhanced flexural strength.
Yaroslav Frolov, Oleksandr Bobukh, Christian Klose, Florian Nürnberger, Hans Jürgen Maier   +4 more
wiley   +1 more source

On g-β-Irresolute Functions on Generalized Topological Spaces

International Journal of Analysis and Applications, 2018
In this paper, we introduce and investigate a new kind of function namely g-β-irresolute function along with its two weak and strong forms in generalized topological spaces. Several characterizations and interesting properties of these functions are discussed.
openaire   +5 more sources

Singularities and Topology of Meromorphic Functions

, 2002
We present several aspects of the "topology of meromorphic functions", which we conceive as a general theory which includes the topology of holomorphic functions, the topology of pencils on quasi-projective spaces and the topology of polynomial functions.
A Dimca, A Dimca, A Dold, A Parusiriski, AH Durfee, B Teissier, B Teissier, C Sabbah, C Sabbah, D Burghelea, D Siersma, D. Siersma, D.T. Lê, DT Lê, DT Lê, E Brieskorn, EH Spanier, F Pham, H Hamm, HV Ha, J Briançon, J Briançon, J-L Verdier, JP Henry, L Fourrier, M Tibàr, M Tibár, M Tibár, M Tibár, M. Morse, N A’Campo, N A’Campo, O Zariski, P Deligne, R García López, R García López, R Switzer, R Thom, S Gusein, S Gusein-Zade, S Gusein-Zade, SA Broughton, SA Broughton, T Gaffney, VA Vassiliev, VI Arnol’d, VI Arnol’d, W Ebeling, WD Neumann, WD Neumann   +49 more
core   +1 more source

Additive Manufacturing of Continuous Fibre Reinforced Composites: Process, Characterisation, Modelling, and Sustainability

Advanced Engineering Materials, EarlyView.
Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley   +1 more source

Phase Field Failure Modeling: Brittle‐Ductile Dual‐Phase Microstructures under Compressive Loading

Advanced Engineering Materials, EarlyView.
The approach by Amor and the approach by Miehe and Zhang for asymmetric damage behavior in the phase field method for fracture are compared regarding their fitness for microcrack‐based failure modeling. The comparison is performed for the case of a dual‐phase microstructure with a brittle and a ductile constituent.
Jakob Huber, Jan Torgersen, Ewald Werner
wiley   +1 more source

Lipschitz functions on topometric spaces

, 2013
We study functions on topometric spaces which are both (metrically) Lipschitz and (topologically) continuous, using them in contexts where, in classical topology, ordinary continuous functions are used.
Yaacov, Itaï Ben
core   +2 more sources