Results 211 to 220 of about 957,237 (288)

Machine Learning‐Guided Design of Cu–Ni–Sn Alloys With Tailored Ni3Sn/Ni3Sn2 Precipitates

Materials Genome Engineering Advances, EarlyView.
To address the trade‐off between strength and conductivity in Cu–Ni–Sn alloys, this study proposes a new closed‐loop design strategy that integrates machine learning, thermodynamic calculations, and experimental verification from the perspective of “phase selectivity”, providing a new approach for multiphase control and synergistic improvement of multi‐
Fei Tan, Wei Chen, Jingpeng Yu, Jiaqi Lan, Zixuan Zhao, Yanbin Jiang, Zhu Xiao, Wenqin Xu, Meng Wang, Guofu Xu, Zhou Li   +10 more
wiley   +1 more source

On the Vapor Pressures, Phase Transitions, and Solid-State Fluorescence of 2-(2-Hydroxyphenyl)benzoxazole and 2-(2-Hydroxyphenyl)benzothiazole. [PDF]

Chemphyschem
Silva Ferraz JM, Silva ALR, Romagnoli L, Ciccioli A, Freitas VLS, Ribeiro da Silva MDMC, Ribeiro da Silva MDMC, Vecchio Ciprioti S.   +7 more
europepmc   +1 more source

Quantitative Evaluation of Surface Whitening Mitigation via Thermal Annealing in Carbon Fiber/Polyphenylene Sulphide Thermoplastic Composite Laminates

Polymer Composites, EarlyView.
Mitigation of surface whitening in CF/PPS laminates via thermal annealing and quantitative image‐based assessment. ABSTRACT Surface whitening is a manufacturing‐induced surface defect in thermoplastic composites, resulting from non‐uniform shrinkage and near‐surface resin instability during cooling.
JongHun Baek, Hyunseok Choi, Tae‐Yeong So, Chan Joo Lee, Jinsu Gim, Hyun‐Taek Lee, Dongearn Kim   +6 more
wiley   +1 more source

Advances in Phase Change Materials for Thermal Energy Storage and Management: Challenges and Enhancement Strategies. [PDF]

ACS Omega
Muhabie AA, Mengesha WG, Yang X.
europepmc   +1 more source

Impact of Waste‐Derived Slate Dust on Structural, Thermal, and Thermomechanical Behavior of Recycled Poly(Ethylene Terephthalate)

Polymer Composites, EarlyView.
This study investigates the use of waste slate dust as a filler in recycled PET. Incorporating up to 20 wt% slate dust caused no filler‐induced molecular degradation, increased the crystallization temperature, thermal conductivity, and storage modulus. ABSTRACT Recycled polyethylene terephthalate (rPET) is widely considered a sustainable alternative to
Aditya Chauhan, Tej Singh, Andrea Fiorati, Sampat Singh Bhati, László Lendvai, Luigi De Nardo, Robert Brüll   +6 more
wiley   +1 more source

Combined Effects of Thermal Cycling Aging and Reinforcement Content on the Ball‐On‐Disk Wear of Additively Manufactured Polylactic Acid Composites

Polymer Composites, EarlyView.
Thermal Aging and Tribological Tests of Additive Manufactured PLA Composites. ABSTRACT This study focuses on the additive manufacturing of pure polylactic acid (PLA) specimens and milled glass fiber (GF)‐filled PLA composites under thermal cycling aging and wear tests. Wear tracks have been analyzed via 3D optical profiling and SEM imaging.
Sinan Fidan, Satılmış Ürgün, Nevin Gamze Karsli, Taner Yilmaz, Mustafa Özgür Bora, Mehmet İskender Özsoy   +5 more
wiley   +1 more source

Preparation and performance evaluation of expanded vermiculite-based phase change materials for building thermal insulation and energy saving. [PDF]

RSC Adv
Fan C, Zhang H, Gao J, Yang H, Lv X.
europepmc   +1 more source

Behavior of Injection‐Molded Nylon 6 Composites With Virgin and Field‐Exposed Waste‐Recycled Blends

Polymer Composites, EarlyView.
Recycling field‐exposed Nylon 6 composites for sustainable secondary applications. ABSTRACT Every year, more than 18,600 metric tonnes of glass fiber‐reinforced Nylon 6 composite waste from sucker rod guides used in downhole oil and gas applications are landfilled due to uncertainty about retained performance after prolonged service exposure.
Chundu Gyem Tamang, Allan Manalo, Paulomi (Polly) Burey, Wahid Ferdous, Tristan Shelley, Mayur Patel, Tony Chapman   +6 more
wiley   +1 more source

Analysis of Melting Phenomena of the Alkali Halides: What Causes the Low Melting Points of the Lithium Halides? [PDF]

J Mass Spectrom
Zeneyedpour L, Burgers PC.
europepmc   +1 more source

Effect of Carbon Nanotubes Incorporation on the Properties of a Photopolymer Resin Used in Vat Photopolymerization

Polymer Composites, EarlyView.
Preparation and experimental results of carbon nanotube/photopolymer resin nanocomposites fabricated by 3D printing. ABSTRACT This work examines the effect of the incorporation of carbon nanotubes (CNTs) into a photopolymer resin for the fabrication of nanocomposites via additive manufacturing (AM), using the masked stereolithography technique (MSLA ...
Caio Kuribayashi, Matheus Campos Hemkemaier, Guilherme Mariz de Oliveira Barra, Marcio Roberto da Rocha, Bluma Guenther Soares, Claudia Merlini   +5 more
wiley   +1 more source