Results 161 to 170 of about 32,953 (312)

Topological Point Defects in SmC* Liquid Crystals Under Mechanical Disturbance

Advanced Materials Interfaces, EarlyView.
Tangetial air jet shear inducess island formation and nucleates topological point defects in uniform SmC films. Island bounded by edge dislocation loops shrink and transform into isolated point defects under continued shear. Mechanical perturbatio provides a controllable route for defect engineering in smectric liquid crystal thin films.
Gunganist Kongklad, Vandana Molahalli, Apichart Pattanaporkratana, Nattaporn Chattham   +3 more
wiley   +1 more source

Hydrogel‐Based 3D‐Printable Stretchable Pressure Sensor

Advanced Materials Technologies, EarlyView.
We present a carbon‐black‐functionalized double‐network granular hydrogel (DNGH) pressure sensor capable of detecting pressures from 200 Pa, equivalent to a light finger touch, up to 500 kPa. The sensor exhibits signal drifts below 3.5% after 800 cycles and response times around 80 ms. Leveraging this broad sensing range, we 3D print this material into
Tianyu Yuan, Chenzhuo Li, Antonia Georgopoulou, John M. Kolinski, Esther Amstad   +4 more
wiley   +1 more source

Affymetrix probes containing runs of contiguous guanines are not gene-specific [PDF]

, 2008
High Density Oligonucleotide arrays (HDONAs), such as the Affymetrix HG-U133A GeneChip, use sets of probes chosen to match specified genes, with the expectation that if a particular gene is highly expressed then all the probes in the designated probe set
Andrew P. Harrison, Graham J. Upton, William B. Langdon   +2 more
core   +1 more source

Transducers Across Scales and Frequencies: A System‐Level Framework for Multiphysics Integration and Co‐Design

Advanced Materials Technologies, EarlyView.
Transducers convert physical signals into electrical and optical representations, yet each mechanism is bounded by intrinsic trade‐offs across bandwidth, sensitivity, speed, and energy. This review maps transduction mechanisms across physical scale and frequency, showing how heterogeneous integration and multiphysics co‐design transform isolated ...
Aolei Xu, Mengyao Xiao, Zhouli Sui, Yinpeng Wang, Daoye Zheng, Yuxin Liu, Luwei Wang, Huajun Liu, Chengkuo Lee   +8 more
wiley   +1 more source

Unlocking the Potential of MXene‐Based Electrochemical Biosensors: A Review of Biofunctionalization Strategies and Biosensing Principles

Advanced Materials Technologies, EarlyView.
ABSTRACT Electrochemical biosensors enable the accurate and timely detection of clinical biomarkers, improving healthcare and precision medicine. MXene nanosheets, a class of 2D transition metal carbides, nitrides, and carbonitrides, are promising materials for developing next‐generation electrochemical biosensors due to their unique physicochemical ...
Muhsin Ali, Sharat Chandra Barman, Isobel Steer, Aya H. Alshareef, Dana Alsulaiman   +4 more
wiley   +1 more source

Optofluidic Raman Analysis and Capacity Recovery in Li‐ion Cells

Advanced Materials Technologies, EarlyView.
Operando Raman spectroscopy is used to monitor the degradation of commercial Li‐ion cells. Using a microfluidic access port, small amounts of electrolyte are sampled into a hollow‐core optical fibre, where fibre‐enhanced Raman analysis reveals Li+ solvation changes and solvent evolution.
Ermanno Miele, Wesley M. Dose, Ian A. K. Davidson, Hesham Sakr, Natalie V. Wheeler, Francesco Poletti, Michael De Volder, Clare P. Grey, Jeremy J. Baumberg, Tijmen G. Euser   +9 more
wiley   +1 more source

High‐Power Rapid Laser‐Induced Synthesis of Multi‐functional Cobalt Metal‐Organic Framework With an Unprecedented Synthesis Efficiency

Advanced Materials Technologies, EarlyView.
Laser‐assisted synthesis enables rapid (within 1 h) and high‐yield (≥90%) production of Co‐MOFs with mesoporous structures, tunable magnetic and optical properties, and efficient adsorption of N2, CH4, and CO2 for low‐energy gas separation. DFT calculations elucidate the electronic structure and adsorption behavior.
Saliha Mutlu, Bülend Ortaç, Ali Karatutlu, Taylan Gorkan, Engin Durgun, Dilek Soyler, Saniye Soylemez, Jelena Lillepäg, Volkan Filiz, Nergis Arsu, Sevil Savaskan Yilmaz   +10 more
wiley   +1 more source

Distance-dependent duplex DNA destabilization proximal to G-quadruplex/i-motif sequences [PDF]

, 2017
G-quadruplexes and i-motifs are complementary examples of non-canonical nucleic acid substructure conformations. G-quadruplex thermodynamic stability has been extensively studied for a variety of base sequences, but the degree of duplex destabilization ...
Evans, Amanda C., Huppert, Julian L., König, Sebastian L. B., Sigel, Roland K. O.   +3 more
core  

Exciton Radiative Lifetimes in Hexagonal Diamond Ge and SixGe1–x Alloys

Advanced Optical Materials, EarlyView.
Strong room‐temperature photoluminescence reported in hexagonal Ge conflicts with theory predicting a nearly dark band edge. First‐principles calculations of excitonic radiative lifetimes fill a key gap in this debate, showing that pristine hexagonal Ge remains intrinsically weakly emissive, while Si alloying only modestly shortens the lifetime and ...
Michele Re Fiorentin, Michele Amato, Maurizia Palummo   +2 more
wiley   +1 more source

3D‐Printing Aided Rapid Prototyping of Pretensioned Tensegrity Structures for Robotic Applications

Advanced Robotics Research, EarlyView.
Printing, injection molding, and assembly (PMA) is a method for rapid prototyping mesoscale, topologically complex, and tensioned tensegrity structures. In combination with PMA method, two mold design strategies: modular mold and compact channel layout, enable efficiency and scalability for tensegrity fabrication.
Yi Sun, Jan Petrš, Omar Aloui, Dario Floreano   +3 more
wiley   +1 more source