Results 71 to 80 of about 240,163 (350)
Advanced Energy and Sustainability Research, EarlyView.Hydrogen is an energy carrier, produced from renewable and nonrenewable resources. It can be stored in a variety of materials and transported to distant locations. This article reviews progress in hydrogen technology by looking at environmental and economic impact, cost analysis, and policy support at government level as way forward for bringing it to ...
Xuexue Pan +5 more
wiley +1 more source
Thermal and structural modelling of arc welding processes: A literature review
Measurement + Control, 2019 This paper presents a state-of-the-art critical review of the thermal and structural modelling of the arc welding process. During the welding process, high temperature in the welding zone leads to generation of unwanted residual stresses and results in ...
Hitesh Arora +2 more
doaj +1 more source
Effect of GTAW on the Tensile Strength and Hardness of Mild Steel
Annals of "Dunarea de Jos" University of Galati, Fascicle XII, Welding Equipment and Technology, 2022 Gas tungsten metal arc welding (GTAW) is used to study the effect of the base metal thickness, welding current and welding speed on the tensile strength and hardness of mild steel welding.
S. Elfallah
doaj +1 more source
Recent Progress in Silver Nanowire‐Based Transparent Conductive Electrodes
Advanced Energy and Sustainability Research, EarlyView.This work has reviewed silver nanowire‐based transparent conductive electrodes in terms of synthesis strategies, device fabrication processes, composition engineering, and property tailoring for flexible electronic applications. The developments of silver nanowire‐based platforms in sensors, solar cells, electronic skin, electromagnetic shielding ...
Jintao Wang +5 more
wiley +1 more source
Advances in 3D and 4D Printing of Soft Robotics and Their Applications
Advanced Intelligent Systems, EarlyView.This article summarizes the development of 3D‐printed soft robotics in the recent decade. The article discusses the printing capabilities of different additive manufacturing technologies in terms of soft polymers, multimaterial printability, soft robotic printing, and 4D printing.
Hao Liu +5 more
wiley +1 more source
Investigation into feasibility of hybrid laser-GMAW process for welding high strength quenched and tempered steel [PDF]
, 2012 In this study, the feasibility of hybrid laser-gas metal arc welding process for replacement of conventional flux-cored arc welding procedure for welding high strength quenched and tempered steel was investigated.
Callaghan, Mark +5 more
core +1 more source
Analysis of fumes emitted during hard facing of FCAW wires [PDF]
, 2017 Flux Cored Arc Welding (FCAW) wires are widely used for hard facing as they provide high deposition efficiency, wear resistance and faster speed rates than the solid wire used in Gas Metal Arc Welding process. Flux Cored Arc Welding process employs cored
G, V. P. (Venkatakrishnan) +1 more
core +1 more source
A Review of the Use of Chemical Stabilisation Methods for Lithium‐Ion Batteries
Battery Energy, EarlyView.The review reveals that while chemical stabilisation techniques for recycling EOL LIBs are widely used, many studies overlook safety risks, focusing on quick, low‐cost methods. Only a few studies address the associated hazards, highlighting the need for safer, well‐understood stabilisation processes in battery recycling. ABSTRACT The increasing amounts
Mark D. Williams‐Wynn +1 more
wiley +1 more source
A Multi-Sensor Interface to Improve the Learning Experience in Arc Welding Training Tasks [PDF]
arXiv, 2021 This paper presents the development of a multi-sensor user interface to facilitate the instruction of arc welding tasks. Traditional methods to acquire hand-eye coordination skills are typically conducted through one-to-one instruction where trainees must wear protective helmets and conduct several tests.
arxiv
Derivation of forces acting on the liquid weld metal based on arc pressure measurements produced using alternating shielding gases in the GTAW process [PDF]
, 2013 As part of an ongoing process to fully evaluate the effects of an alternating shielding gas supply on the gas tungsten arc and gas metal arc welding processes, a comparison between arc pressures produced using argon, helium, alternating gases and GTAW-P ...
Campbell, Stuart +2 more
core