Results 191 to 200 of about 1,745,962 (311)
Objective We investigated whether a diagnosis of rheumatoid arthritis (RA) affects the quality of inpatient acute myocardial infarction (AMI) care and long‐term mortality post‐AMI. Methods We analyzed data from 784,091 adults, 6,047 with a diagnosis of RA, from England and Wales hospitalized with AMI between 2005 and 2019 from the Myocardial Ischaemia ...
Megan Butler +8 more
wiley +1 more source
Objective Systemic lupus erythematosus (SLE) is a heterogenous inflammatory condition with widely varying global prevalence estimates. The frequency of SLE in the general population of Australia has been reported to be notably lower than contemporary estimates in countries such as the United States or United Kingdom, at 19 to 39 per 100,000 as opposed ...
Lucinda Roper +7 more
wiley +1 more source
Introduction Rheumatic and musculoskeletal diseases(RMDs) are leading causes of physical disability, necessitating support with activities of daily living(ADLs). This study describes social care received by patients with RMDs in two disperate regions of England: Salford(urban) and Norfolk(rural).
Mehreen Somro +6 more
wiley +1 more source
Associations of Rheumatoid Arthritis Disease Activity with Frailty Over Five Years of Follow‐up
Objective To evaluate whether rheumatoid arthritis (RA) disease activity is associated with frailty both in cross‐section and longitudinally. Methods Participants within the Veterans Affairs Rheumatoid Arthritis registry enrolled from 2003 to 2022 were included. The exposure was RA disease activity measured by Disease Activity Score in 28‐joints (DAS28)
Courtney N. Loecker +14 more
wiley +1 more source
Systemic sclerosis (SSc) is a rare autoimmune disease defined by immune dysregulation, vasculopathy, and progressive fibrosis of the skin and internal organs. Despite advances in care, major complications such as interstitial lung disease (ILD) and myocardial involvement remain the leading causes of morbidity and mortality.
Cristiana Sieiro Santos +2 more
wiley +1 more source
A Robust Adaptive One‐Sample‐Ahead Preview Super‐Twisting Sliding Mode Controller
Block Diagram of the Robust Adaptive One‐Sample‐Ahead Preview Super‐Twisting Sliding Mode Controller. ABSTRACT This article introduces a discrete‐time robust adaptive one‐sample‐ahead preview super‐twisting sliding mode controller. A stability analysis of the controller by Lyapunov criteria is developed to demonstrate its robustness in handling both ...
Guilherme Vieira Hollweg +5 more
wiley +1 more source
The stability criteria affecting the formation of high‐entropy alloys, particularly focusing in supersaturated solid solutions produced by mechanical alloying, are analyzed. Criteria based on Hume–Rothery rules are distinguished from those derived from thermodynamic relations. The formers are generally applicable to mechanically alloyed samples.
Javier S. Blázquez +5 more
wiley +1 more source
Bistable Mechanisms 3D Printing for Mechanically Programmable Vibration Control
This work introduces a 3D‐printed bistable mechanism integrated into tuned mass dampers (TMDs) for mechanically adaptive passive vibration suppression. Through optimized geometry, the bistable design provides adaptable vibration reduction across a broad range of scenarios, achieving effective vibration mitigation without complex controls or external ...
Ali Zolfagharian +4 more
wiley +1 more source
Thermoreflectance Detection of Point Defects Resulting from Focused Ion Beam Milling
Focused ion beam (FIB) milling is a common tool for nanoscale material processing, however irradiation damage, redeposition, and contamination can occur. We use several characterization tools to show FIB‐induced effects beyond 1 mm from the milled area.
Thomas W. Pfeifer +3 more
wiley +1 more source
Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials
Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai +2 more
wiley +1 more source

