Results 91 to 100 of about 29,210 (259)

Hard interfaces with microstructure: the cases of strain gradient elasticity and micropolar elasticity

Philosophical Transactions of the Royal Society A: Mathematical, Physical and Engineering Sciences
As the size of a layered structure scales down, the adhesive layer thickness correspondingly decreases from macro- to micro-scale. The influence of the material microstructure of the adhesive becomes more pronounced, and possible size effect phenomena can appear.
Serpilli M., Rizzoni R., Lebon F.
openaire   +3 more sources

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Defect Evolution and Mechanical Performance of Fused Filament Fabrication‐Manufactured 17‐4PH Stainless Steel Revealed by X‐Ray Computed Tomography

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky, Márk Sárközi, Ibolya Zsoldos, Zoltán Weltsch   +3 more
wiley   +1 more source

Design and Analysis of Compression–Torsion Coupling Metamaterials Using the Golden Section Method

Advanced Engineering Materials, EarlyView.
A novel compression–torsion metamaterial is engineered using inclined rods and symmetry breaking. To optimize its torsional performance, the golden section method is employed. The mechanical response of the metamaterial is validated through both numerical analysis and experimental validation.
Amirhossein Hassani, Sara Bagherifard
wiley   +1 more source

Laser‐Induced Graphene from Waste Almond Shells

Advanced Functional Materials, EarlyView.
Almond shells, an abundant agricultural by‐product, are repurposed to create a fully bioderived almond shell/chitosan composite (ASC) degradable in soil. ASC is converted into laser‐induced graphene (LIG) by laser scribing and proposed as a substrate for transient electronics.
Yulia Steksova, Anna Chiara Bressi, Marina Galliani, Attilio Marino, Gianni Ciofani, Eduardo Machado‐Charry, Hilda Gomez Bernal, Alessandra Francini, Luca Sebastiani, Francesco Greco   +9 more
wiley   +1 more source

Control of Polarization and Polar Helicity in BiFeO3 by Epitaxial Strain and Interfacial Chemistry

Advanced Functional Materials, EarlyView.
In BiFeO3 thin films, the interplay of interfacial chemistry, electrostatics, and epitaxial strain is engineered to stabilize homohelicity in polarization textures at the domain scale. The synergistic use of a Bi2O2‐terminated Aurivillius buffer layer and a highly anisotropic compressive epitaxial strain offers new routes to control the polar‐texture ...
Elzbieta Gradauskaite, Lilia Huynh, Natascha Gray, Quintin N. Meier, Marta D. Rossell, Morgan Trassin   +5 more
wiley   +1 more source

Gradient-Based Optimization of Linear Elasticity Mesh Deformation Quality

International Journal of Aerospace Engineering
Mesh deformation based on the linear elasticity method is crucial in aerospace engineering research. However, maintaining mesh quality after significant deformations can be challenging.
Jinxin Zhou, Xiaojun Wu, Bing Chen, Jing Yu, Shenshen Liu, Hongyin Jia   +5 more
doaj   +1 more source

Counterion Dependent Side‐Chain Relaxation Stiffens a Chemically Doped Thienothiophene Copolymer

Advanced Functional Materials, EarlyView.
Oxidation of a thienothiophene copolymer, p(g3TT‐T2), via different doping strategies and dopant molecules resulted in materials with similar oxidation levels and a high electrical conductivity of ≈100 S cm−1. However, mechanical properties varied significantly, with sub‐glass transition temperatures and elastic moduli spanning from –44°C to –3°C and ...
Mariavittoria Craighero, Meghna Jha, Elsa Veronica Flores‐Vela, Joost Kimpel, Andreas Schaefer, Jiali Guo, Jesika Asatryan, Alberto Peinador Veiga, Shuichi Haraguchi, Per‐Anders Carlsson, Jaime Martín, Mariano Campoy‐Quiles, Christian Müller   +12 more
wiley   +1 more source

Ferroelectricity in Antiferromagnetic Wurtzite Nitrides

Advanced Functional Materials, EarlyView.
We establish MnSiN2${\rm MnSiN}_2$ and MnGeN2${\rm MnGeN}_2$ as aristotypes of a new multiferroic wurtzite family that simultaneously exhibits ferroelectricity and antiferromagnetism with altermagnetic spin splitting. By strategically substituting alkaline‐earth metals, we predict new materials with coexisting switchable polarization, spin texture, and
Steven M. Baksa, Lin‐Ding Yuan, Stephen D. Wilson, James M. Rondinelli   +3 more
wiley   +1 more source

Strain‐Programmable Luminescent Adhesive Patch With Tartrazine‐Mediated Optical Skin Clearing for Photochemical Tissue Bonding

Advanced Functional Materials, EarlyView.
We propose a suture‐complementary approach that integrates optical skin clearing with a strain‐programmable luminescent adhesive patch. Hyaluronic acid promotes transdermal delivery of tartrazine to improve optical clearing and stabilizes its interaction with a photosensitizer. Optical clearing increases the penetration depth of visible light into skin,
Seong‐Jong Kim, Kyungjoo Jo, Kwanghyeon Park, Jun Hee Kim, Jong Hyeong Cho, Inhoo Choi, Sei Kwang Hahn   +6 more
wiley   +1 more source