Results 201 to 210 of about 852,102 (246)

Spontaneous grain refinement effect of rare earth zinc alloy anodes enables stable zinc batteries. [PDF]

Natl Sci Rev
Chen M, Gong Y, Zhao Y, Song Y, Tang Y, Zeng Z, Liang S, Zhou P, Lu B, Zhang X, Zhou J.   +10 more
europepmc   +1 more source

The Significance of Coherent Transformation on Grain Refinement and Consequent Enhancement in Toughness. [PDF]

Materials (Basel), 2020
Li X, Zhao J, Dong L, Misra RDK, Wang X, Wang X, Shang C.   +6 more
europepmc   +1 more source

From the Discovery of the Giant Magnetocaloric Effect to the Development of High‐Power‐Density Systems

Advanced Materials Technologies, EarlyView.
The article overviews past and current efforts on caloric materials and systems, highlighting the contributions of Ames National Laboratory to the field. Solid‐state caloric heat pumping is an innovative method that can be implemented in a wide range of cooling and heating applications.
Agata Czernuszewicz, Yaroslav Mudryk, Jun Cui, Lucas Griffith, Duane D. Johnson, Julie Slaughter   +5 more
wiley   +1 more source

Hierarchical Multi‐Material Architectures With Gradient Design for Dynamic‐Range Flexible Tactile Sensing

Advanced Materials Technologies, EarlyView.
Hierarchical multi‐material TPMS lattices are engineered as flexible tactile sensors by combining soft and stiff elastomeric layers with a conformal conductive coating. The bilayer architecture delivers sensitivity at low pressures while maintaining a broad detectable range under large loads, enabling reliable pressure and vibration monitoring for ...
Reza Noroozi, Domenic Quiquero, Yan Yan Shery Huang, HaoTian Harvey Shi   +3 more
wiley   +1 more source

Separative and Comprehensive Effects of Grain Coarsening and Grain Refinement of Ni-38Cr-3.8Al Alloy during Thermal Deformation Process. [PDF]

Materials (Basel)
Quan G, Zhao Y, Deng Q, Quan M, Yu Y, Wu D.   +5 more
europepmc   +1 more source

Aerosol Jet Printing of Benzocyclobutene as a Thermally Stable, Low‐Loss Dielectric for Multilayer Microwave Electronics

Advanced Materials Technologies, EarlyView.
Multilayer aerosol jet printed components with a low‐loss, thermally stable dielectric are demonstrated using benzocyclobutene. Ink formulation and in‐line droplet evaporation control support high‐quality, versatile, and stable printing performance. A specialized measurement for low‐loss materials reveals promising microwave properties, which, combined
Md Ramjan Ali, Trent Moritz, Mohammad Tayeb Al Qaseer, Ethan B. Secor   +3 more
wiley   +1 more source

Programmable Crack Networks for Wide‐Range and Reversible Strain Sensing in Vertically Oriented van der Waals Molybdenum Disulfide Thin Films

Advanced Materials Technologies, EarlyView.
Vertically oriented van der Waals MoS2 thin films enable a mechanically programmable crack network for strain sensing. The initial mechanical programming protocol establishes a programmed crack configuration along weak interlayer and interdomain interfaces.
Yinli Wang, Hiroyuki Hirakata
wiley   +1 more source

In‐House Manufacturing of 3D ECM Culture Chips via Vacuum Thermoforming for Enhanced Imaging Applications

Advanced Materials Technologies, EarlyView.
Desktop vacuum thermoforming enables rapid, low‐cost fabrication of 96‐channel polystyrene culture chips with very thin imaging interfaces. The resulting platform supports cell lines, primary cells, and patient‐derived organoids, and enables high‐resolution confocal microscopy and single‐cell visualization, providing an accessible approach for advanced
Aleksandra Fomina, Adam Tam, Jennifer Lam, Nila C. Wu, Nancy T. Li, Alison P. McGuigan   +5 more
wiley   +1 more source

Superplastic Deformation of Al-Cu Alloys after Grain Refinement by Extrusion Combined with Reversible Torsion. [PDF]

Materials (Basel), 2020
Rodak K, Kuc D, Mikuszewski T.
europepmc   +1 more source

Two‐Step Thermal Upcycling of Flexible Printed Circuit Board Waste Into Metallic Copper Nanoparticles: Synthesis and Characterization

Advanced Materials Technologies, EarlyView.
A two‐step thermal upcycling process converts flexible printed circuit board waste into high‐purity copper nanoparticles using polymer degradation and arc discharge. The synthesized nanoparticles exhibit controlled morphology and high metal purity.
Bikesh S. Ghinangju, Rumana Hossain, Veena Sahajwalla   +2 more
wiley   +1 more source