Results 111 to 120 of about 1,092,040 (293)
Advanced Engineering Materials, EarlyView.Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios +5 more
wiley +1 more source
The prediction of the evolution of grain size of land-gear forging during the die-forging process
MATEC Web of Conferences, 2015 The land-gear forgings are the most important structure parts, made of high strength steel 300M. Because of the bad service environment, the microstructure and performance of the part are very strict requirements.
Lin Gao +4 more
doaj +1 more source
Characterizing thermal conduction in polycrystalline graphene
, 2013 Thermal conduction was explored and discussed through a combined theoretical and simulation approach in this work. The thermal conductivity k of polycrystalline graphene was calculated by molecular dynamics simulations based on a hexagonal patch model in
Song, Zhigong, Wang, Yanlei, Xu, Zhiping
core +1 more source
Advanced Engineering Materials, EarlyView.Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source
Remote SensingSnow grain size is important in albedo calculation, mass balance, and climate research. Critically, in situ measurements of snow grain size on the Tibetan Plateau remain scarce.
Yunlong Zhang, Yixiang Tian
doaj +1 more source
Advanced Engineering Materials, EarlyView.Nickel‐based alloys are widely used in high‐temperature applications due to their excellent mechanical strength and oxidation resistance. However, properties such as high‐temperature strength and pronounced work‐hardening make them difficult to machine.
Soheil Rooein +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi +2 more
wiley +1 more source
The effect of Sm2O3 on the sintering and grain growth behaviors of SnO2-based ceramics [PDF]
, 2019 The effect of samarium oxide was examined on the sintering, microstructure, and grain growth behaviors of (Co, Nb)-doped SnO2-based ceramics prepared by co-precipitation method.
Bastami, Hajieh +3 more
core +1 more source
Advanced Engineering Materials, EarlyView.The presented study focuses on the fracture behaviour of carbon‐bonded magnesia MgO–C refractories, where environmentally friendly fructose, collagen and lignin serve as temporary binding agents. The partial substitution of the source material with recycled MgO–C reduces the fracture resistance, which can be counteracted by the additional introduction ...
Marc Neumann +6 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm +5 more
wiley +1 more source