Results 101 to 110 of about 227 (192)

Workflow to facilitate complete denture scanning with an intraoral scanner: A technique report

Journal of Prosthodontics, EarlyView.
Abstract Scanning a denture with an intraoral scanner is typically more challenging than scanning a dentate arch. This article describes a novel technique for digitally duplicating a complete denture. The workflow involves scanning an existing denture using an intraoral scanner with the addition of specific markers and subsequently constructing a ...
Jiayi Yu, Jiayi Lu, Berna Saglik, Junying Li   +3 more
wiley   +1 more source

Influence of prosthesis type and intraoral scanner‐based extraoral scanning protocol on the passive fit of CAD‐CAM verification devices

Journal of Prosthodontics, EarlyView.
Abstract Purpose To evaluate the impact of different complete‐arch digital scanning techniques and prosthesis types on the passive fit of computer‐aided design and computer‐aided manufacturing (CAD‐CAM) verification devices. Materials and Methods Two different maxillary master casts with four multi‐unit abutment (MUA) implant analogs (FP‐1 and FP‐3 ...
Toshiki Nagai, Yusuke Kuroda, Natalie Asavanant, Chao‐Chieh Yang, Dean Morton, Wei‐Shao Lin   +5 more
wiley   +1 more source

Assessment of fit accuracy and retentive strength of additively manufactured zirconia crowns luted to Ti‐base abutments with different resin cements: An in vitro study

Journal of Prosthodontics, EarlyView.
Abstract Purpose This study investigated the influence of cement gap size on the marginal and internal fit, and cement gap size and type on retention of additively manufactured zirconia (AM‐Z) crowns on titanium bases (Ti‐base). Materials and Methods A total of 135 zirconia crowns were designed with three different cement gap sizes: 20 µm, 30 µm, and ...
Rafat Sasany, Sultan Merve Uçar, Burak Yilmaz   +2 more
wiley   +1 more source

MXene Inks for High‐Throughput Printing of Electronics

Advanced Electronic Materials
MXene inks are promising alternatives for conventional conductive inks in printing electronics. However, the formulation of MXene inks is challenging due to the physicochemical properties of the few solvents in which MXenes can be dispersed. Furthermore,
Sina Abdolhosseinzadeh, René Schneider, Mohammad Jafarpour, Céline Merlet, Frank Nüesch, Chuanfang (John) Zhang, Jakob Heier   +6 more
doaj   +1 more source

Effect of margin thickness and cement gap on the fabrication and fit accuracy of additively manufactured crowns in definitive resins with different filler content

Journal of Prosthodontics, EarlyView.
Abstract Purpose To evaluate how commercially available composite resins in varying filler content affect the fabrication and fit accuracy (trueness and precision) of additively manufactured (AM) definitive crowns with different margin thickness and cement gaps by comparing them to subtractively manufactured (SM) polymer‐infiltrated ceramic crowns ...
Mustafa Borga Dönmez, Gülce Çakmak, Çiğdem Kahveci, Amir H. Nejat, Burak Yilmaz, Pinar Altinci   +5 more
wiley   +1 more source

Bond strength enhancement for additively manufactured zirconia: Micro‐retentive design approach

Journal of Prosthodontics, EarlyView.
Abstract Purpose To investigate the effect of digitally designed micro‐retention features on the bond strength of additively manufactured (AM) zirconia copings. Materials and Methods Sixty titanium base abutments (NobelParallel, NobelBiocare), pretreated with 50 µm alumina particles were divided into four groups (n = 15 per group); one group with ...
Rama B. Al‐Rashdan, Charles Beard, Fei Liu, Berna Saglik, Bashar A. Al‐Rashdan, Khaled Q. Al Hamad   +5 more
wiley   +1 more source

Effect of material, prosthesis height, and aging on the fracture strength of additively and subtractively manufactured implant‐supported cantilevered prostheses

Journal of Prosthodontics, EarlyView.
Abstract Purpose This study aimed to evaluate the inherent and after cyclic loading fracture strength of implant‐supported cantilevered fixed prostheses fabricated from recently introduced additively manufactured (AM) and subtractively manufactured (SM) materials, considering variations in prosthesis height.
Mustafa Borga Dönmez, Paola Maldonado, Çiğdem Kahveci, Ahmet Orgev, Marta Revilla‐León, Burak Yilmaz, Gülce Cakmak   +6 more
wiley   +1 more source

Influence of different manufacturing materials on the accuracy and fitting of full‐arch restorations using a photogrammetry scanner—In vitro study

Journal of Prosthodontics, EarlyView.
Abstract Purpose This study aimed to assess the accuracy of a photogrammetry scanner and evaluate the influence of four different manufacturing materials on the accuracy and fitting of full‐arch restorations made using a photogrammetry scanner. Materials and Methods A cast with six implant abutment analogs was made.
Paulo Sergio Borella, Abidiel Silva Guimaraes, Thais Silva Mendonça, Gus Khalil, Sandra Al‐Tarawneh, Lyndon F. Cooper, Gustavo Mendonça   +6 more
wiley   +1 more source

Effects of printing temperature and post‐curing duration on the dimensional reproducibility and fracture load of 3D‐printed dental prostheses: An exploratory study

Journal of Prosthodontics, EarlyView.
Abstract Purpose This in vitro study aimed to evaluate the effects of printing temperature and post‐curing duration on the dimensional reproducibility and mechanical properties of three‐dimensional (3D)–printed dental prostheses. Materials and Methods Photopolymer specimens were fabricated using a stereolithographic 3D printer at two temperatures: room
Ji‐Min Lee, KeunBaDa Son, Kyu‐Bok Lee   +2 more
wiley   +1 more source

Prosthetic designs for complete dentures manufactured using contemporary 3D printing techniques: A case series with clinical, design, and laboratory considerations

Journal of Prosthodontics, EarlyView.
Abstract Advancements in additive manufacturing have enabled the precise fabrication of complete dentures using modern photopolymers and diverse 3D printing techniques. These innovations have transformed removable prosthodontics by allowing clinicians to design and manufacture highly customized prostheses to manage difficult anatomical and esthetic ...
Francisco X. Azpiazu‐Flores, Abdullah M. Aldosari, Paola C. Saponaro, Kedith Sawangsri, Wei‐Shao Lin   +4 more
wiley   +1 more source