Results 201 to 210 of about 44,267 (264)

From the Discovery of the Giant Magnetocaloric Effect to the Development of High‐Power‐Density Systems

Advanced Materials Technologies, EarlyView.
The article overviews past and current efforts on caloric materials and systems, highlighting the contributions of Ames National Laboratory to the field. Solid‐state caloric heat pumping is an innovative method that can be implemented in a wide range of cooling and heating applications.
Agata Czernuszewicz, Yaroslav Mudryk, Jun Cui, Lucas Griffith, Duane D. Johnson, Julie Slaughter   +5 more
wiley   +1 more source

Talkative battery: super-safe batteries with power-modulation based internal and external sensor data collection. [PDF]

Commun Eng
Diers J, Beiranvand H.
europepmc   +1 more source

Enhanced Infection Resistance and Regenerative Healing of Titanium Implants via Peptide‐Loaded Biodegradable Coatings

Advanced Materials Technologies, EarlyView.
This study presents a new biodegradable coating for titanium implants using a natural antimicrobial peptide, caerin 1.9. Applied via solvent casting, the coating offers sustained antibacterial protection and promotes healing. Tested on 3D‐printed porous titanium scaffolds, it effectively prevented infection—including against resistant bacteria—while ...
Hejie Li, Tianfang Wang, Nicolas Soro, Guoying Ni, Meg Allom, D. İpek Kurtböke, Xiaosong Liu, Damon Kent   +7 more
wiley   +1 more source

Polydopamine-doped PEDOT interfaces improve cell-electrode interactions and neural signal transmission. [PDF]

Sci Rep
Ahmadi Seyedkhani S, Kalhor S, Iraji Zad A, Vafaiee M, Taghipoor M, Mohammadpour R.   +5 more
europepmc   +1 more source

Elastomers Combining Damping Efficiency With Rapid Recovery

Advanced Materials Technologies, EarlyView.
Double network granular elastomers (DNGEs) combine high energy dissipation under both cyclic loading and high impact with rapid shape recovery. 3D printing enables the production of complex, customizable structures with tailored performance. Recyclable DNGEs retain their properties over multiple recycling cycles.
Eva Baur, Alain Molleyres, Esther Amstad
wiley   +1 more source

Research on wind power penetration limit considering voltage stability. [PDF]

Sci Rep
Liu X, Zhang Y, Li H, Zu W.
europepmc   +1 more source

Overcoming Printing and Interfacial Challenges in Liquid Metal Direct Writing for Integrated Stretchable Electronics

Advanced Materials Technologies, EarlyView.
Liquid metal direct writing is advanced from a technological and fundamental point. Utilizing a kinematic bed, printing on large surfaces with irregularities is enabled. Furthermore, a pressure‐driven flow during printing is discovered that affects the thickness of traces.
Maximilian Krack, Lennert Purnal, Parth Vinayakrao Sewlikar, Sam Cuyvers, Gus Geurts, Rathul Nengminza Sangma, Derese Desta, Dieter Reenaers, Bart Ruttens, Iris De Graeve, Tom Hauffman, Seppe Terryn, Bram Vanderborght, Michaël Daenen, Wim Deferme, Monika Rai   +15 more
wiley   +1 more source

Multi-timescale energy-aware grid-forming control with self-tuning virtual inductance for battery lifetime enhancement. [PDF]

Sci Rep
Zheng L, Liu X.
europepmc   +1 more source

End‐to‐End Sensing Systems for Breast Cancer: From Wearables for Early Detection to Lab‐Based Diagnosis Chips

Advanced Materials Technologies, EarlyView.
This review explores advances in wearable and lab‐on‐chip technologies for breast cancer detection. Covering tactile, thermal, ultrasound, microwave, electrical impedance tomography, electrochemical, microelectromechanical, and optical systems, it highlights innovations in flexible electronics, nanomaterials, and machine learning.
Neshika Wijewardhane, Lyn I. Jones, Richard M. Martin, Helen Winter, Faezeh Arab Hassani   +4 more
wiley   +1 more source

Bioinspired acoustic metasurface for simultaneous bilateral wave manipulation. [PDF]

Discov Nano
Xiao H, Yu J, Yan M, Song X, Xu J, Bai J, Zhou J.   +6 more
europepmc   +1 more source