Results 41 to 50 of about 121,256 (303)
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Matrix-filler interactions in a co-ground ecocomposite: surface properties and behaviour in water [PDF]
, 2011 Ecocomposites made up of polystyrene and starch were produced by co-grinding. The mechanism by which the composite is formed was identified by following the particle size and morphology.
Lamure, Alain +2 more
core +2 more sources
Advanced Engineering Materials, EarlyView.This study examines how several molten high‐silicon electrical steels interact with both conventional and recycled MgO–C refractories. For this, various immersion experiments are conducted. In addition to infiltration, a number of mechanisms are identified and explained that control the corrosion of the refractory material.
Lukas Neubert +7 more
wiley +1 more source
External grind-hardening forces modelling and experimentation [PDF]
The International Journal of Advanced Manufacturing Technology, 2013 Grind hardening process utilizes the heat generated in the grinding area for the surface heat treatment of the workpiece. The workpiece surface is heated above the austenitizing temperature by using large values of depth of cut and low workpiece feed speeds.
Salonitis, Konstantinos +2 more
openaire +3 more sources
Geometrical analysis of thread milling – Part 1: Evaluation of tool angles [PDF]
, 2010 Thread milling is a method which is increasingly used for machining thread. For this operation, a helical interpolation is required. Furthermore, the thread mill is a tool whose geometry is rather complex.
FROMENTIN, Guillaume, POULACHON, Gérard
core +2 more sources
Advanced Engineering Materials, EarlyView.High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé +5 more
wiley +1 more source
Jin'gangshi yu moliao moju gongchengObjectivesWith the rapid development of industrial automation and intelligent manufacturing, the application of industrial robots in the stone processing industry has garnered increasing attention.
Fusen WU
doaj +1 more source
Model coupling friction and adhesion for steel-concrete interfaces
, 2009 The interface behaviour between steel and concrete, during pull-out tests, is numerically investigated using an interface model coupling adhesion and Coulomb friction. This model, first developed by Raous, Cang\'emi, Cocou and Monerie (RCCM), is based on
Karray, M'hamed Ali, Raous, Michel
core +3 more sources
Effects of bearing clearance on the chatter stability of milling process [PDF]
, 2010 In the present study, the influences of the bearing clearance, which is a common fault for machines, to the chatter stability of milling process are examined by using numerical simulation method.
Altintas +32 more
core +1 more source
Zein‐Based Adhesives: Sustainable Extraction and Application in Bioadhesive Technologies
Advanced Engineering Materials, EarlyView.Zein is extracted from corn gluten meal using a simple and scalable process with high yield (~90%). The resulting protein is applied in bioadhesives modified with Ca2+ and Fe3+ ions, exhibiting substrate‐dependent adhesion. The findings demonstrate competitive bonding performance and highlight the role of ionic interactions in tuning adhesion ...
Paula Bertolino Sanvezzo +3 more
wiley +1 more source