Results 91 to 100 of about 351,640 (302)

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source

Investigating overlapping deformation patterns of the Beijing Plain by independent component analysis of InSAR observations

International Journal of Applied Earth Observations and Geoinformation
Due to policies such as groundwater extraction restrictions, water diversion, and water replenishment, groundwater levels in the Beijing Plain have generally risen.
Shangjing Lai, Jinxin Lin, Jie Dong, Jianzhong Wu, Xinlei Huang, Mingsheng Liao   +5 more
doaj   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

Momentum distribution in heavy deformed nuclei: role of effective mass

, 2004
The impact of nuclear deformation on the momentum distributions (MD) of occupied proton states in $^{238}$U is studied with a phenomenological Woods-Saxon (WS) shell model and the self-consistent Skyrme-Hartree-Fock (SHF) scheme.
E. Chabanat, E. N. Shurshikov, J. Mesa, P.-G. Reinhard, T. H. R. Skyrme, V. A. Chepurnov, V. O. Nesterenko, V. O. Nesterenko, V. P. Likhachev, V. V. Pashkevich, W. Kleinig   +10 more
core   +1 more source

NFDI MatWerk Ontology (MWO): A BFO‐Compliant Ontology for Research Data Management in Materials Science and Engineering

Advanced Engineering Materials, EarlyView.
This article presents the NFDI‐MatWerk Ontology (MWO), a Basic Formal Ontology‐based framework for interoperable research data management in materials science and engineering (MSE). Covering consortium structures, research data management resources, services, and instruments, MWO enables semantic integration, Findable, Accessible, Interoperable, and ...
Hossein Beygi Nasrabadi, Ebrahim Norouzi, Kostiantyn Hubaiev, Jörg Waitelonis, Harald Sack   +4 more
wiley   +1 more source

dMODELS. A free software package to model volcanic deformation [PDF]

, 2018
Shallow magma accumulation in the crust often results in slight movements of the ground surface that can be measured using standard land-surveying techniques or satellite geodesy.
Battaglia, Maurizio
core  

Effect of deformation on two-neutrino double beta decay matrix elements

, 2006
We study the effect of deformation on the two-neutrino double beta decay for ground state to ground state transitions in all the nuclei whose half-lives have been measured. Our theoretical framework is a deformed QRPA based in Woods-Saxon or Hartree-Fock
A. Faessler, Akimune, Barabash, E. Moya de Guerra, F. Šimkovic, Homma, L. Pacearescu, P. Sarriguren, R. Álvarez-Rodríguez, Álvarez-Rodríguez, Šimkovic   +10 more
core   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Breaking rotational symmetry in two-flavor color superconductors

, 2003
The color superconductivity under flavor asymmetric conditions relevant to the compact star phenomenology is studied within the Nambu-Jona-Lasinio model.
A. Sedrakian, A.I. Larkin, A.K. Leibovich, A.W. Steiner, B. Barrois, D. Bailin, H. Müther, H. Müther, H. Müther, J. Berges, J. Kundu, J.A. Bowers, J.A. Bowers, K. Iida, K. Rajagopal, M. Alford, M. Alford, M. Buballa, M. Kitazawa, M.G. Alford, M.G. Alford, M.G. Alford, P. Fulde, P.F. Bedaque, R. Casalbuoni, R. Casalbuoni, R. Casalbuoni, R. Casalbuoni, R. Rapp, R.D. Pisarski, T.M. Schwarz, W.V. Liu   +31 more
core   +1 more source

Microstructural Evolution and Vacancy Defect Formation in Mn–Mo–Ni RPV Steel Under Low Cycle Fatigue: Insights From EBSD and PALS

Advanced Engineering Materials, EarlyView.
Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar, Dhanadeep Dutta, G. Bharat Reddy   +2 more
wiley   +1 more source