Results 131 to 140 of about 2,138,910 (305)
Advanced Engineering Materials, EarlyView.This perspective reframes additive manufacturing for electrical machines as a qualification‐limited materials and architecture design problem. It links process–structure–property–performance relationships to magnetic, conducting, dielectric, and thermal property windows, highlighting where AM can enable segmented magnetic circuits, permanent magnet ...
Dénes Fodor, Loránd Szabó
wiley +1 more source
Advanced Engineering Materials, EarlyView.Near‐surface deuterium enrichment profiles for different microstructural types of TiAl after exposure at 700 °C in a heavy water‐containing environment. The deuterium levels are significantly higher than expected from natural occurrence, indicating that the heavy water dissociated during the exposure treatment and entered the specimens.
Jonathan D. H. Paul +5 more
wiley +1 more source
, 2016 As a continuation of Part 1 of ground support modelling involving large ground deformation by Saiang and Nordlund (2016) this paper presents the conceptual models and results from the typically observed cases throughout the Kristineberg mine.
Nordlund, Erling,, Saiang, David,
core
Advanced Engineering Materials, EarlyView.This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin +12 more
wiley +1 more source
Cross-reference table of grade of damage to surface buildings and ground deformation.
, 2019 Cross-reference table of grade of damage to surface buildings and ground deformation.
Dawei Zhou (1465549) +5 more
core +1 more source
Advanced Engineering Materials, EarlyView.Despite benefits to storage stability and handleability of aluminum scrap, octadecyl phosphonic acid (ODPA) SAMs reduce the tensile strength of wires produced using friction‐induced recycling. Etching and methyl diphosphonic acid (MDPA) coatings, however, have little effect.
Timothy D. Goller +3 more
wiley +1 more source
DEFORMATION OF COMPOSITE GROUND DURING CONSOLIDATION
Doboku Gakkai Ronbunshu, 1992 杭状のドレーン材を含む複合地盤の圧密変形解析を行うために, ドレーン材の剛性, ドレーンによる排水効果および透水係数の劣化を考慮した有限要素法の計算手法を提案し, 砂杭と正規圧密粘土より成る複合地盤の圧密変形を解析した結果, 間隙水圧の消散過程を妥当に計算できることを示した. さらに, 圧縮率および置換率の異なる複合地盤を解析し, 沈下量, 圧密速度および応力分担比などについて考察した.
openaire +2 more sources
Advanced Engineering Materials, EarlyView.A high interstital austenitic steel is additively manufactured and postdensified by HIP to eliminate gas porosity. Thereby, the loss of N and Mn in Ar HIP atmosphere is investigated. Further, HIP using N2 atmosphere is investigated which led to excessive nitride formation.
F. Großwendt +4 more
wiley +1 more source
Regional Modeling of Liquefaction-Induced Ground Deformation
, 2002 Liquefaction-induced ground deformations are permanent ground displacements resulting from earthquakes, which can extend over areas as large as a few square kilometers and have amplitudes ranging from a few centimeters to few tens of meters. This type of
Tetsuo Tobita +7 more
core +1 more source
Electrodeposition in Structural Lattices of Variable Architectures
Advanced Engineering Materials, EarlyView.Electrodeposition enables geometry‐sensitive, autonomous void filling while simultaneously tuning chemical and mechanical properties. The development of approaches that can autonomously fill and heal material voids and yield composites with tailorable properties is increasingly relevant in engineering.
Yeong‐Man Kwon +3 more
wiley +1 more source