Results 161 to 170 of about 5,350,968 (279)

Comment on "Artificial intelligence enhanced contemporary pulmonary hypertension care". [PDF]

Am Heart J Plus
Princiba DB, Kulkarni RR.
europepmc   +1 more source

3D‐Printed Titanium Gyroid Scaffold Structure Integrated With Tough Hybrid Materials for Cartilage Replacement

Advanced Engineering Materials, EarlyView.
This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin, Gloria R. Young, Francesca Tallia, Reece N. Oosterbeek, Shaaz Ghouse, Edward Spiers, Nupur Kohli, Tom Briggs, Marc Masen, Siwei Li, Ren‐Jei Chung, Jonathan R. T. Jeffers, Julian R. Jones   +12 more
wiley   +1 more source

Communication-infrastructure-enabled ISAC for low-altitude sensing. [PDF]

Commun Eng
Feng Z, Wang L, Yu K, Wei Z, Zhang Q, Ma D, Li J, Wei J, Zhang P.   +8 more
europepmc   +1 more source

The Role of Ultra‐Thin Passive Films and Organic Adsorbates on Aluminum Chips for a Friction‐Induced Solid‐State Recycling Process

Advanced Engineering Materials, EarlyView.
Despite benefits to storage stability and handleability of aluminum scrap, octadecyl phosphonic acid (ODPA) SAMs reduce the tensile strength of wires produced using friction‐induced recycling. Etching and methyl diphosphonic acid (MDPA) coatings, however, have little effect.
Timothy D. Goller, Steffen Gabsa, Werner Homberg, Guido Grundmeier   +3 more
wiley   +1 more source

Patient Posture-Adaptive Non-Contact Respiratory Rate Measurement Inside a Moving Ambulance Using RGB and Thermal Cameras. [PDF]

Diagnostics (Basel)
Nemoto D, Takahashi N, Mukouyama F, Nakada TA, Nomura Y, Nakaguchi T.   +5 more
europepmc   +1 more source

Impact of the Process Atmosphere During Hot Isostatic Pressing on the Near‐Surface Composition of an Additively Manufactured Austenitic High‐Interstitial Steel

Advanced Engineering Materials, EarlyView.
A high interstital austenitic steel is additively manufactured and postdensified by HIP to eliminate gas porosity. Thereby, the loss of N and Mn in Ar HIP atmosphere is investigated. Further, HIP using N2 atmosphere is investigated which led to excessive nitride formation.
F. Großwendt, J. Hahn, J. Kimm, S. Weber, J. Lentz   +4 more
wiley   +1 more source

Mobile-Master-Vehicle-Based LiDAR Perception and Centralized Control of Sensor-Light Slave Vehicles. [PDF]

Sensors (Basel)
Shin H, Kwak J, Moon H, Bae S, Mung NX, Kim M.   +5 more
europepmc   +1 more source

Thermal Cycle–Microstructure–Property Relationships in Rail Steel Heat‐Affected Zone Simulated by Gleeble

Advanced Engineering Materials, EarlyView.
Microstructural evolution of premium rail steel during flash butt welding (FBW), comparing physically simulated heat‐affected zones with actual weld regions. Thermal cycles induce phase transformations and microstructural heterogeneity that influence weld quality and mechanical performance. These findings provide insights into optimizing FBW parameters
Emmanoelle Cintra da Cunha Araújo, João Marcos da Silva Nunes, Marcelly Cristiny Nunes de Carvalho, Alex Rojas, Cristie Luis Kugelmeier, Cristhian Ricardo Loayza Loayza, João Carlos Ferreira, Maria Veronica Goncalves Rodrigues, Rute Sayuri Kano, Isaac Araújo Furtado, Jacyara Dalylla da Silva Nunes, Jhonatan Peres de Sousa, Marcos Natan da Silva Lima, Eden Santos Silva, Gedeon Silva Reis, Samuel Filgueiras Rodrigues   +15 more
wiley   +1 more source

How the characteristics of a virtual environment affects the perception of travel distance through it. [PDF]

PLoS One
Bansal A, McManus M, Harris LR.
europepmc   +1 more source

Gyroid Structured Globugraphite Carbon Foam With Hierarchical and Tailored Pore Size

Advanced Engineering Materials, EarlyView.
Secondary sacrificial templates were designed and printed to create a defined network within a porous carbon. Lattices thermally degrades during the sintering process. Lattices are imprinted into the ceramic template and transferred to the morphology of Globugraphite.
Christiane Roller, Justin Neumann, David Ploch, Lennard M. Flohr, Julian Karsten, Fabian A. Riebesehl, Bodo Fiedler   +6 more
wiley   +1 more source