Results 171 to 180 of about 1,362,980 (290)

Fault Diagnosis and Location Method for Stator-Winding Single-Phase Grounding of Large Generator Based on Stepped-Frequency Pulse Injection. [PDF]

Sensors (Basel)
Lei B, Xu S, Liu Y, Zu W, Yu M, Guo Y, Dong L, Cheng Z.   +7 more
europepmc   +1 more source

Interactions between Molten High‐Silicon Electrical Steels and Carbon‐Bonded MgO Refractories Based on Recyclates

Advanced Engineering Materials, EarlyView.
This study examines how several molten high‐silicon electrical steels interact with both conventional and recycled MgO–C refractories. For this, various immersion experiments are conducted. In addition to infiltration, a number of mechanisms are identified and explained that control the corrosion of the refractory material.
Lukas Neubert, Matheus Roberto Bellé, Anton Yehorov, Anhelina Mospan, Till M. J. Stadtmüller, Seetharaman Sridhar, Christos G. Aneziris, Olena Volkova   +7 more
wiley   +1 more source

Performance assessment of compression ground anchors in urban deep excavations through numerical and field investigations. [PDF]

Sci Rep
Akbas M, Demirci G, Ozdemir BB, Iyisan R.   +3 more
europepmc   +1 more source

Hybrid Auxetic Architectures: Integrating Curvature‐Driven Design for Enhanced Mechanical Tunability and Structural Performance

Advanced Engineering Materials, EarlyView.
Curvature‐tuned auxetic lattices are designed, fabricated, and mechanically characterized to reveal how geometric curvature governs stretchability, stress redistribution, and Poisson's ratio evolution. Photoelastic experiments visualize stress pathways, while hyperelastic simulations quantify deformation mechanics.
Shuvodeep De, Giovanni Meli, Meysam Khaleghian, Anahita Emami   +3 more
wiley   +1 more source

Impact of energy metabolism pathways in promoting phytoremediation of cadmium contamination by Bacillus amyloliquefaciens Bam1. [PDF]

Bioresour Bioprocess
Jiang X, Chen X, Gao H, Luo J, Zhang L, Luo Y, Wu H.   +6 more
europepmc   +1 more source

Multimodal Mechanical Testing of Additively Manufactured Ti6Al4V Lattice Structures: Compression, Bending, and Fatigue

Advanced Engineering Materials, EarlyView.
In this experimental study, the mechanical properties of additively manufactured Ti‐6Al‐4V lattice structures of different geometries are characterized using compression, four point bending and fatigue testing. While TPMS designs show superior fatigue resistance, SplitP and Honeycomb lattice structures combine high stiffness and strength. The resulting
Klaus Burkart, Jonas Schmidt, Anastasiya Toenjes, Johanna Eisenträger   +3 more
wiley   +1 more source

Mechanisms of pile-soil stress and deformation in excavations under the coupled effects of excavation disturbance and extreme rainfall infiltration. [PDF]

Sci Rep
Wang X, Zhang Y, Li W, Xiao J, Tan F, Huang C.   +5 more
europepmc   +1 more source

Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6

Advanced Engineering Materials, EarlyView.
The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter, Thomas Wegener, Andreas Schilling, Martin Fehlbier, Thomas Niendorf   +4 more
wiley   +1 more source

Ground Resistance Measurements and Evaluation of Grounding Electrodes Performance [PDF]

Annals of computer science and information systems
Konstantinos Koutras, Eleni Tsolou, Georgios Peppas, Apostolos Samiotis, Eleftheria Pyrgioti   +4 more
doaj   +1 more source

Rapidly Progressive Pulmonary Hypertension: Importance of Vascular Disease Distribution. [PDF]

Circulation
Tada A, Fayyaz AU, Reddy YNV, Redfield MM, Borlaug BA.   +4 more
europepmc   +1 more source