Results 171 to 180 of about 10,438 (299)

Complex estimation of mechanical properties of SLM-printed gyroid AlSi10Mg structures – experimental and FE analysis

Shaheer UI Hassan, Mazahir Hussain Shah, S. Parma, Jan Štefan, Luděk Pešek, Miroslav Chomat   +5 more
openalex   +1 more source

Harnessing Macromolecular Crowding of Proteins for Engineering Sustainable Nanofiltration Membranes

SusMat, Volume 6, Issue 2, April 2026.
Novel biodegradable and solvent‐resistant nanofiltration membranes fabricated by harnessing the macromolecular crowding of zein protein induced by solvent interactions. Scattering experiments and molecular dynamics simulations confirmed the macromolecular crowding formation and revealed the structural characteristics of the membranes.
Claudia Oviedo, Diana G. Oldal, Rifan Hardian, Tibor Holtzl, Maged F. Serag, Satoshi Habuchi, Gyorgy Szekely   +6 more
wiley   +1 more source

Metamaterials from Plasma-Treated Block Copolymer Monolith. [PDF]

ACS Appl Mater Interfaces
Chen C, Chuang JC, Yin KH, Tung CH, Yang KC, Hung YC, Lee CC, Ho RM.   +7 more
europepmc   +1 more source

Modeling of Deformation Behavior of Gyroid and I-WP Polymer Lattice Structures with a Porosity Gradient

, 2021
Nataliya Elenskaya, Mikhail Tashkinov
openalex   +1 more source

Alumina–Zirconia Composite Filaments for 3D‐Printed Scaffolds With Bioglass Infiltration for Medical Applications

International Journal of Applied Ceramic Technology, Volume 23, Issue 2, April 2026.
This study demonstrates the innovative development of alumina–zirconia composite scaffolds produced by fused filament fabrication (FFF) and infiltrated with bioglass via the sol–gel method. The combination yielded highly porous three‐dimensional architectures (500 µm–1 mm), suitable for nutrient diffusion, vascularization, and cell colonization.
Maíra Faccio, Natália Fontana Nicoletti, Bruna Lins, Diego Pires Gurgel, Janete Eunice Zorzi, Jadna Catafesta   +5 more
wiley   +1 more source

Comparative Torsional Properties via Numerical Simulation of Triply Periodic Minimal Surfaces (TPMS): Diamond, Gyroid and Primitive Structures. [PDF]

Polymers (Basel)
Skibar M, Susantyoko RA, Pervaiz S.
europepmc   +1 more source

rG-Same.mp4 from Amorphous bicontinuous minimal surface models and the superior Gaussian curvature uniformity of Diamond, Primitive and Gyroid surfaces

Himmelmann, M., Pedersen, M. C., Klatt, M. A., Schönhöfer, P.W.A., Evans, M. E., Schröder-Turk, G. E.   +5 more
openalex   +1 more source

Chemical vapour deposition of freestanding sub-60 nm graphene gyroids

, 2017
Tomasz Cebo, Adrianus Indrat Aria, James A. Dolan, Robert S. Weatherup, Kenichi Nakanishi, Piran R. Kidambi, Giorgio Divitini, Caterina Ducati, Ullrich Steiner, Stephan Hofmann   +9 more
openalex   +2 more sources

Sintering Improves the Mechanical Properties of Fluorapatite Scaffolds With Open Porous Gyroid Architecture

International Journal of Applied Ceramic Technology, Volume 23, Issue 2, April 2026.
ABSTRACT Synthetic scaffolds are needed to overcome the limitations of autografts and allografts for the treatment of critical‐sized bone defects. However, fabricating scaffolds with both high porosity and adequate mechanical stability for load‐bearing applications is difficult.
Clark Nielson, Jill Shea, Jayant Agarwal, Sujee Jeyapalina   +3 more
wiley   +1 more source

Orientation driven design and mechanical optimization of gyroid TPMS lattice structures. [PDF]

Sci Rep
El-Asfoury MS, El-Bedwehy NE, Shazly M, Elkaseer A.   +3 more
europepmc   +1 more source