Results 81 to 90 of about 2,558,597 (245)

Active range of motion outcomes after reconstruction of burned wrist and hand deformities.

open access: yes, 2016
This works aim is to evaluate the efficacy of skin grafts and flaps in reconstruction of post-burn hand and wrist deformities. A prospective study of 57 burn contractures of the wrist and dorsum of the hand was performed.
Afifi, Ahmed M   +5 more
core   +1 more source

Craniofacial Deformities

open access: yes, 2022
Craniofacial deformities (CFA) includes deformities in the head and facial bones. Such abnormalities are developed since birth .
Dr. Shadab Mohammad
core   +1 more source

Investigating the Low‐Temperature Phase Stability of the Binary Ta–W System

open access: yesAdvanced Engineering Materials, EarlyView.
Atomistic simulations show that the binary Ta–W system forms ordered intermetallic phases, B2‐TaW and D03‐TaW3, as 0 K ground states. Configurational entropy, however, lowers the free energy of the disordered bcc solid solution, which becomes the stable phase above about 400 K.
Klemens Lechner   +7 more
wiley   +1 more source

Cryogenic Deformation Behavior of TiAl and Insights Into Embrittlement After High‐Temperature Exposure Combined With Secondary Ion Mass Spectroscopy of Near Surface Chemistry

open access: yesAdvanced Engineering Materials, EarlyView.
Near‐surface deuterium enrichment profiles for different microstructural types of TiAl after exposure at 700 °C in a heavy water‐containing environment. The deuterium levels are significantly higher than expected from natural occurrence, indicating that the heavy water dissociated during the exposure treatment and entered the specimens.
Jonathan D. H. Paul   +5 more
wiley   +1 more source

Surgical treatment of hand deformities in multiple enchondromatosis: a case report

open access: yesActa Orthopaedica et Traumatologica Turcica, 2021
Multiple enchondromatosis (Ollier’s disease) is a rare disease characterized by widespread enchondromas. In general, the short tubular bones of the hand are involved, with progressive lesions resulting in cosmetic problems and functional deformities ...
Bulent Erol   +4 more
doaj  

Enhancement of the Through‐Thickness Electrical Conductivity of Carbon‐Fiber‐Reinforced Plastics Using Large Graphite Particles

open access: yesAdvanced Engineering Materials, EarlyView.
To enhance through‐thickness conductivity without sacrificing impregnation, large spherical graphite particles are intentionally employed in a low‐viscosity resin. Unlike finer conductive fillers, these particles remain outside the fiber bundles and accumulate in resin‐rich interlaminar regions during molding.
Keito Hosoe   +6 more
wiley   +1 more source

The Role of Ultra‐Thin Passive Films and Organic Adsorbates on Aluminum Chips for a Friction‐Induced Solid‐State Recycling Process

open access: yesAdvanced Engineering Materials, EarlyView.
Despite benefits to storage stability and handleability of aluminum scrap, octadecyl phosphonic acid (ODPA) SAMs reduce the tensile strength of wires produced using friction‐induced recycling. Etching and methyl diphosphonic acid (MDPA) coatings, however, have little effect.
Timothy D. Goller   +3 more
wiley   +1 more source

Elastic–Plastic Modeling and Experimental Characterization of Granular Jamming Actuators

open access: yesAdvanced Engineering Materials, EarlyView.
Granular jamming enables rapid switching between soft and rigid mechanical states. Here, a reduced‐order elastic‐perfectly‐plastic beam framework captures pressure‐dependent loading, unloading, residual deformation, and hysteresis in jammed beams, while matching three‐point bending experiments across materials and geometries. The framework links design
Saheli Patel   +2 more
wiley   +1 more source

CONGENITAL ANOMALIES OF THE UPPER LIMBS IN A UNIVERSITY CENTER: A CROSS-SECTIONAL STUDY [PDF]

open access: yesActa Ortopédica Brasileira
Objective: To identify the prevalence and characteristics of CAULs treated at a university center, aiming to improve epidemiological understanding and management of these conditions.
Danilo José Leite Gomes   +5 more
doaj   +1 more source

Mitigating Creep Anisotropy and Enhancing Performance in Additively Manufactured Ni‐Based Superalloys: A Review

open access: yesAdvanced Engineering Materials, EarlyView.
Additive manufacturing introduces pronounced microstructural and crystallographic anisotropy in Ni‐based superalloys, resulting in orientation‐dependent creep deformation and damage. This review identifies the key microstructural origins of creep anisotropy, examines their influence on dominant deformation mechanisms, and highlights processing ...
Chandan Kumar   +3 more
wiley   +1 more source

Home - About - Disclaimer - Privacy