Review on Tooth Flank Fracture Failure of Hardened Gears
Jixie chuandong, 2022 There is a new tooth failure mode for hardened gears called tooth flank fracture(TFF). ISO published a technical specification for calculating the load capacity of tooth flank failure in 2019.
Zhigang Cao +6 more
doaj +2 more sources
Experimental Investigation of Laser Surface Transformation Hardening of 4340 Steel Spur Gears
Journal of Manufacturing and Materials Processing, 2019 This paper presents an experimental investigation of laser surface transformation hardening (LSTH) of 4340 steel spur gears using regression analysis.
Al Khader Borki +2 more
doaj +2 more sources
Study on Tooth Interior Fatigue Fracture Failure of Wind Turbine Gears
Metals, 2020 Gear contact fatigue has becoming a bottleneck restricting the safety and reliability of wind turbine transmission systems. Tooth interior fatigue fracture (TIFF) failure is commonly observed in case-hardened wind turbine gears.
Houyi Bai +5 more
doaj +2 more sources
Tooth Surface Deviation Analysis for Continuous Generation Grinding of Internal Gears
Applied SciencesIn order to resolve the issues of low efficiency and poor precision in the traditional finishing process of hardened internal gears, a method is proposed for calculating the profile curves of a drum-shaped grinding tool suitable for mass finishing of ...
Jianjun Yang +3 more
doaj +2 more sources
Layer Approach to Model Fatigue Strength of Surface-Hardened Components
MetalsThis paper deals with a surface-hardened forged steel that is commonly used for powertrain components like gears, axles or crankshafts. In order to increase static and fatigue strength and to minimise wear, surface treatments like induction hardening ...
Dénes Dobberke +3 more
doaj +2 more sources
Deterministic Analytical Model of Resistance to Deep Contact Fatigue of a Stressed Material
Механика машин, механизмов и материалов, 2021 The stress state of the surface layer in the contact zone of the mating teeth of cylindrical gears is considered. It is shown that under contact loading, the stress state of the surface layer is inhomogeneous and changes with the distance from the ...
Sergei P. Rudenko, Sergei G. Sandomirski
doaj +1 more source
Grinding the side surfaces of the spiroid cylindrical gear worm turns with a tapered wheel [PDF]
E3S Web of Conferences, 2023 Information about the worms’ production technology of spiroid cylindrical gears is given. A method of the profile analytical calculation of a disk abrasive tool is proposed, providing the possibility to profile grinding wheels for various types of ruled ...
Tkachuk Alexander, Ignatyugin Valery
doaj +1 more source
Influence of Shot Peening on Surface Durability of Case-Hardened Steel Gears
Journal of Advanced Mechanical Design, Systems, and Manufacturing, 2007 In order to investigate the influence of shot peening on the surface durability of case-hardened steel gears, the case-hardened steel gears shot-peened with different shot velocities and shot diameters were fatigue-tested using a power circulating type ...
Masanori SEKI +5 more
doaj +1 more source
EFFECTS OF CARBURIZING AND NITRIDING PROCESSES ON THE COST AND QUALITY OF GEARS PRODUCED WITH AISI 4140 AND 8620 STEELS [PDF]
Tecnologia em Metalurgia, Materiais e Mineração, 2012 This study compares the effects of nitriding and carburizing processes applied to gears subjected to contact stresses below 1300 MPa. The manufacturing cost, as well the depth of hardened layer and the distortion produced by two processes are analyzed.
Claudio José Leitão +2 more
doaj +1 more source
Extended Wear Lifetime Calculation for Grease Lubricated Gears in Consideration of Surface Hardness and Roughness [PDF]
MATEC Web of Conferences, 2022 Greases have a variety of advantages when special operating conditions apply for gear lubrication, e. g. improved properties against continuous (or slow speed) wear.
Siewerin Benedikt J. +2 more
doaj +1 more source