PTA hardfacing of cutting edge for chemical industry
Tato diplomová se zabývá navařením čepele odřezávacího nože zelené skalice metodou PTA. V teoretické části je proveden rozbor problematiky navařování a přídavných materiálů. Experimentální část je zaměřena na tvorbu návarů.
Šimeček Karel
core
Microstructure and Abrasive Wear Behaviour of Shielded Metal Arc Welding Hardfacing used in Agricultural Implements [PDF]
The abrasive wear behavior of hypereutectic and hypoeutectic based Fe-Cr-C hardfacing are reported and interpreted in terms of the microstructures. The coating were deposited onto a Mild steel substrate by shielded metal arc welding using two commercial ...
, Dr. K. M. Kenchi Reddy, Dr. C. T. Jayadeva
core +1 more source
Waste-based consumable for hardfacing by welding: a look from the Circular Economy
In the present work, the obtaining of a consumable for the restore parts by welding from the perspective of the circular economy is addressed, using industrial solid residuals (slag from steel production, graphite from fragments of electrodes of arc ...
Azucena Elizabeth Bernal-Gutiérrez +5 more
doaj +1 more source
Improving Ballistic Resistance of Armor Steel by FCAW with Hardfacing Alloys of Fe–Mo–Mn–B–C System
Armor steels can be strengthened against modern ballistic threats through surface hardfacing with advanced Fe-based alloys. This study develops a series of flux-cored arc welded (FCAW) hardfacing alloys in the Fe–Mo–Mn–B–C system to enhance the ballistic
Prysyazhnyuk Pavlo +7 more
doaj +1 more source
Hardfacing of 3.5% Cr Steel by Flux Cored Wire Are Welding Process [PDF]
วิศวกรรมศาสตรมหาบัณฑิต (วิศวกรรมวัสดุ), 2561Hardfacing weld is a technique which mainly extends the service life of engineering components. The purpose of this research is to study wear behavior of hardfacing welded on 3.5% chromium cast steel by Flux ...
ธีรโชติ ตรีเภรี
core +2 more sources
LASER CLADDING WITH COBALT-BASED HARDFACING ALLOYS
Preliminary results aimed at designing Co-based hardfacing alloys specifically for the laser cladding process are reported. Three alloys, ranging from hypo- to hypereutectic were deposited using scanning velocities between 1.7 and 170 mm/s.
J.-D. WAGNIÈRE, A. FRENK
core +1 more source
Optimizing the laser parameters to attain maximum hardness in nickel based hardfacing surfaces
In this investigation, an attempt has been made to optimize the laser hardfacing (LH) parameters such as power, powder feed rate (PFR), travel speed and defocusing distance to maximize hardness of Ni-based hardfacing surfaces.
Gnanasekaran S. +4 more
doaj +1 more source
Development of hardfaced crusher jaws using ferro-alloy hardfacing inserts and low carbon steel substrate [PDF]
Procedures for producing hardfaced jaws using ferro-alloy hardfacing inserts and low carbon steel substrate have been established. This research was prompted by the need to provide an economical substitute to the high manganese austenitic steel that has ...
Chijioke Okechukwu +4 more
doaj
Ni-Mo-Cr-B Alloys: Corrosion Resistant Amorphous Hardfacing Coatings
A series of rapidly solidified Ni-Mo-Cr-B alloys have been investigated for possible application as corrosion resistant hardfacing coatings. As-cast amorphous ribbons were pulverized to powder, which was subsequently applied to a substrate by plasma ...
R. L. Bye, E. M. Norin, S. K. Das
core +1 more source

