Results 91 to 100 of about 508,157 (301)
Advanced Engineering Materials, EarlyView.The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi +3 more
wiley +1 more source
Литьë и металлургия, 2019 The regularities of the formation of powders based on the Fe-Al system, obtained by the method of mechanical alloying and intended for the deposition of thermal spraying coatings were established.
F. G. Lovshenko, A. S. Fedosenko
doaj +1 more source
What Do Large Language Models Know About Materials?
Advanced Engineering Materials, EarlyView.If large language models (LLMs) are to be used inside the material discovery and engineering process, they must be benchmarked for the accurateness of intrinsic material knowledge. The current work introduces 1) a reasoning process through the processing–structure–property–performance chain and 2) a tool for benchmarking knowledge of LLMs concerning ...
Adrian Ehrenhofer +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin +2 more
wiley +1 more source
Қарағанды университетінің хабаршысы. Физика сериясы, 2018 The multi-component nitride coverings on the basis of (Zr-Ti-Nb)N, (Zr-Ti-Cr-Nb)N and (Zr-Ti-Cr-Nb-Si)N are received by the method of vacuum-arc deposition from multielement cathodes Zr-Ti-Nb, Zr-Ti-Cr-Nb, Zr-Ti-Cr-Nb-Si in the environment of nitrogen ...
D.K. Yeskermessov +2 more
doaj
Materials Research LettersBalancing the hardness and electrical conductivity of copper alloys within complex compositions and processes poses a formidable challenge. This study proposes a strategy combining machine learning with the Pareto front techniques to identify optimal ...
Hang Fu +8 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Multi-component (Ti-Zr-Cr-Nb)N coatings’: structure and properties
Қарағанды университетінің хабаршысы. Физика сериясы, 2017 In the article discusses the results of the deposition of nanostructured coatings obtained by vacuum arc deposition of cathode (Ti-Zr-Cr-Nb), and analyzes their structure, morphology, elemental composition, and tribological properties (friction, wear ...
D.K. Yeskermessov +2 more
doaj
Process Optimization in Laser Welding of IN792 DS Superalloy
MetalsNi-base superalloys are employed to produce parts of aeronautic engines, space vehicles and power plants. During the production process or lifetime of components, cracks may occur which affect their performance.
Giuseppe Barbieri +7 more
doaj +1 more source
Elinvar Materials: Recent Progress and Challenges
Advanced Engineering Materials, EarlyView.Elinvar materials, exhibiting temperature‐invariant elastic modulus, are critical for precision instruments and emerging technologies. This article reviews recent progress in the field, with a focus on the anomalous thermoelastic behavior observed in key material systems.
Wenjie Li, Yang Ren
wiley +1 more source