Results 81 to 90 of about 2,518 (205)
Nonconventional Technologies Review, 2020 This article presents experimental studies of microhardness distributions along the depth of the thermally hardened zone in high-quality carbon Steel 45 (analog DIN 1.0503) after wire electrical discharge machining (WEDM) using а wide range of modes ...
Vasyl Osypenko +3 more
doaj
Femtosecond Laser Heat Affected Zones in Aluminum
Microscopy and Microanalysis, 2022 Renae N Gannon +2 more
openaire +1 more source
Advanced Engineering Materials, EarlyView.Different Al/Al bimetals with a single engineered interface reveal how mechanical mismatch governs fatigue crack growth under cyclic loading. Additionally, loading–unloading–reloading tests link the microyielding behavior to the fatigue crack growth resistance, while crack‐path analysis reveals toughening mechanisms at the interface, highlighting ...
Sebastian Vollath +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.During creep of a single‐crystal Ni‐based superalloy, the overall crystal orientation is observed to remain constant while the microstructure evolves. Despite the lack of macroscopic rotation, small (<1°) rotations are observed on the submicron size scale and are accommodated by counteracting rotations over the scale of several micrometers.
E. J. Payton +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Schematic representation of modes of microcrack nucleation, growth and temporary arrestment at different boundaries, with the criteria for crack propagation in three scenarios: (1) large notch, (2) defect/small sharp notch, and (3) long crack. This work revisits and integrates results on the fatigue behavior of advanced bainitic steels (in particular ...
Lucia Morales‐Rivas
wiley +1 more source
Advanced Engineering Materials, EarlyView.Residual adhesive after electrode loading in adhesive‐assisted resistance spot welding is quantified through a traceable experimental‐to‐digital workflow. Chromatic confocal topography provides calibrated surface‐height data, while OpenCV detects the electrode imprint and integrates adhesive height into comparable volume metrics.
Sung‐Min Wi, Jiangdong Zhao
wiley +1 more source
Microstructure and properties of AH36 steel joints by laser-submerged arc hybrid welding
Hanjie xuebaoThe double-sided welding without groove for 16 mm thick AH36 steel plates was conducted by a laser-submerged arc hybrid welding process. The microstructures and mechanical properties of the laser zone and submerged arc zone of the welded joints were ...
Pengbo WU +6 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Postbuild annealing systematically modifies the phase fractions and morphology of EB‐PBF processed Mo–9Si–8B. Quantitative microstructure–property correlations reveal how controlled phase evolution enhances high‐temperature compressive strength and creep resistance.
Christopher Schmidt +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Deep‐UV (258 nm) femtosecond pulses enable uniform amorphous silicon writing on Si(100)/(111) with a six‐fold larger fluence amorphization window than NIR methods. Optimized fluence and overlap yield 20–45 nm uniform and continuous amorphous layers. Microscopy shows sharp interfaces, and real‐time reflectivity reveals nanosecond melt–resolidification ...
Wissal Benali +5 more
wiley +1 more source
Laser‐Induced Graphene from Waste Almond Shells
Advanced Functional Materials, EarlyView.Almond shells, an abundant agricultural by‐product, are repurposed to create a fully bioderived almond shell/chitosan composite (ASC) degradable in soil. ASC is converted into laser‐induced graphene (LIG) by laser scribing and proposed as a substrate for transient electronics.
Yulia Steksova +9 more
wiley +1 more source