Results 21 to 30 of about 5,240,245 (344)
Zavarivanje i zavarene konstrukcije, 2015 Jedan od osnovnih parametara koji utiče na osobine spojeva zavarenih elektrolučnim postupcima je količina unite toplote. Obezbeđenje dovoljne pouzdanosti zavarenih konstrukcija pogotovo konstrukcija izrađenih od čelika povišene i visoke čvrstoće i razvoj
Radomir Jovicic +3 more
openaire +3 more sources
CHARACTERIZATION OF WELD HEAT INPUT EFFECTS ON MECHANICAL PROPERTIES OF Cr-Mo STEEL BAR USING TIG WELDING PROCESS [PDF]
European Journal of Materials Science and Engineering, 2021 Welding as an energy-consuming process is inevitable as-welded joint can be subject to various loads without failure. Therefore, this paper presents the welding thermal cycle of Cr-Mo steel bar (ASTM A304) of dimensions 100 by 50 and various thicknesses ...
Reuben Adebare ADEWUYI +1 more
doaj +1 more source
The Heat Input At Friction Stir Spot Welding
, 2018 The article deals with the technique of friction stir spot welding. The significant element of this technique is to determine the temperature of the material in the zone of stirring which can be determined by calculating the value of the heat input in the welding zone.
STATSENKO VLADIMIR +3 more
openaire +2 more sources
Metals, 2022 Welding is one of the most widely used metal joining techniques. However, improper technique and handling may lead to weld defects. Cracks that occur during the exploitation of the welded joints in places of increased stress concentration are called ...
Miroslav Randić +2 more
doaj +1 more source
Structure and Mechanical Behavior of Heat-Resistant Steel Manufactured by Multilayer Arc Deposition
Metals, 2023 The manuscript demonstrates the structure and the mechanical behavior of a material manufactured by multilayer arc deposition. Three-dimensional printing was performed using OK Autrod 13.14 wire on a substrate of heat-resistant 12Cr1MoV steel in the ...
Ilya V. Vlasov +4 more
doaj +1 more source
Review on effect of heat input for wire arc additive manufacturing process
, 2021 Wire arc additive manufacturing (WAAM) is steadily increasing with significant research work are underway. Ability of WAAM to manufacture a large-scale product at lower cost and shorter lead times has increased its development.
N. Rosli +5 more
semanticscholar +1 more source
Crystals, 2022 In the narrow-gap multi-layer welding of thick Ti-6Al-4V titanium alloy sheets, reducing the number of filling layers can effectively improve the welding efficiency and reduce the possibility of interlayer defects.
Shenghao Meng +4 more
doaj +1 more source
Effect of Heat Input on Microstructure and Corrosion Resistance of CP-Ti Laser Beam Welded Joints
Metals, 2022 The TA1 welded joints with different heat inputs were obtained by a fiber laser and their microstructure, mechanical properties and corrosion resistance in simulated saliva solution were studied.
Zhen Li +4 more
doaj +1 more source
Effect of Heat Input on Microstructure and Corrosion Resistance of X80 Laser Welded Joints
Metals, 2022 Using fiber laser welding technology, X80 pipeline steel welded joints with different welding heat inputs were obtained. Their microstructure, mechanical properties, and corrosion resistance (in NACEA solution saturated with hydrogen sulfide) were ...
Wei Zhao +4 more
doaj +1 more source
Enhancing the Strength of Al/Mg Dissimilar Friction Stir Lap Welded Joint by Zn Filler Addition Combined with an Appropriate Heat Input [PDF]
Archives of Metallurgy and Materials, 2022 7075-T6 Al and AZ31B Mg dissimilar alloys were friction stir lap welded with or without a Zn filler, and the effect of heat input on the joint quality was systematically studied.
Huaxia Zhao +3 more
doaj +1 more source