Results 91 to 100 of about 306,716 (312)
Analysis of Heat Sink Modelling Performance
Elektronika ir Elektrotechnika, 2013 With increasing complexity of electronic components and their systems, their cooling solutions become an important issue, and heat sinks are the most widely applied solution in industry. Theoretical, experimental and numerical methods can be used to determine a heat sinks thermal performance.
Tarvydas, P. +3 more
openaire +1 more source
Morphology‐Controlled Silica Nanoparticle Coatings for Transparent Radiative Cooling
Advanced Materials Interfaces, EarlyView.Transparent radiative cooling coatings are achieved by immobilizing solid and hollow silica spheres on glass. Particle morphology within sub‐monolayer coatings is shown to govern the trade‐off between visible and atmospheric window reflectance. Hollow‐sphere structures enable reduced thermal emission losses while preserving transparency, highlighting ...
Jefferson A. S. Lam +8 more
wiley +1 more source
Engineering ProceedingsHeat sinks have been widely used in cooling systems due to their high heat transfer efficiency. In this study, the thermal performance and fluid flow characteristics of conventional and triply periodic minimal surfaces (TPMS)-based heat sinks were ...
Muhammad Usman Shahid +2 more
doaj +1 more source
, 1978 An electroexplosive device is presented which employs a header having contact pins hermetically sealed with glass passing through from a connector end of the header to a cavity filled with a shunt layer of a new nonlinear resistive composition and a heat-
Menichelli, V. J.
core +1 more source
Reduction of heat sink common-mode currents in switching mode power supply circuits [PDF]
, 2011 In this paper, a new filter design for a heat sink is presented. The parasitic couplings between electric power devices and the heat sink are responsible for common-mode currents.
J. H. Hagmann +3 more
core +1 more source
Mechanical Stress Evolution in Polycrystalline Ge Thin Films Under MeV Ion Irradiation
Advanced Materials Interfaces, EarlyView.Irradiation of polycrystalline Ge thin films with 1.8 MeV Au ions alters residual stress through defect generation and lattice expansion. Increasing fluence drives progressive lattice disorder and eventual amorphization. Polycrystalline Ge resists amorphization longer than crystalline Ge, as grain boundaries facilitate defect diffusion, significantly ...
Karla J. Paz Corrales +10 more
wiley +1 more source
Thermal Conductivity Analysis and Investigation of an Aluminum-Graphene Composite Heat Sink [PDF]
Hangkong bingqiTo address the thermal dissipation challenges caused by high heat flux density in power modules under the high-performance and miniaturization trend of missile-borne electronic devices, this study proposes an innovative solution by optimizing the thermal
Li Hang, Shi Lanfang, Cai Ming
doaj +1 more source
Advanced Materials Technologies, EarlyView.Printed organic thermoelectric generators (OTEGs) enable flexible and sustainable energy harvesting from low‐grade heat. This Perspective critically assesses recent advances in printable thermoelectric materials, 2D and 3D device architectures, and current performance limits of printed OTEGs.
Vijitha Ignatious +5 more
wiley +1 more source
Evanescently-coupled hybrid III-V/silicon laser based on DVS-BCB bonding [PDF]
, 2010 © 2014 IEEE. Controllable electrical breakdown of multiwall nanotubes (MWNTs) is studied utilizing the atomic force microscopy (AFM). Electrical breakdown has been known as the way to fundamentally understand the electrical properties of nanotubes and an
Heck, J +5 more
core +2 more sources
Advanced Materials Technologies, EarlyView.Laser‐assisted synthesis enables rapid (within 1 h) and high‐yield (≥90%) production of Co‐MOFs with mesoporous structures, tunable magnetic and optical properties, and efficient adsorption of N2, CH4, and CO2 for low‐energy gas separation. DFT calculations elucidate the electronic structure and adsorption behavior.
Saliha Mutlu +10 more
wiley +1 more source