Results 201 to 210 of about 14,701,351 (357)

Analysis of Heat Treatment of AlSi7Cu0.5Mg Alloy. [PDF]

Materials (Basel)
Mičian M, Kantoríková E, Borowiecka-Jamrozek J, Kasińska J.   +3 more
europepmc   +1 more source

Research on heat treatment of waste asbestos

Yujia Deng
openalex   +2 more sources

An Investigation into Mechanical Properties of Ductile Cast Iron with Different Heat Treatment Processes

, 2019
Romany R. Moussa, Amer E. Ali, Ragab K. Abdel-Magied, Mohamed N. Elshiekh   +3 more
openalex   +2 more sources

Microstructural Evolution and Mechanical Performance of Plasma‐Assisted Hybrid Friction Stir Welded Dissimilar Aluminum–Copper Joints

Advanced Engineering Materials, EarlyView.
Plasma‐assisted hybrid friction stir welding of dissimilar AlCu joints employs localized plasma preheating to balance heat input and enhance plastic flow. The optimized process reduces axial force by up to 35%, refines the microstructure, and achieves ≈96% joint efficiency.
Deepak Kumar Yaduwanshi, Pankaj Shrivastava, Ganesh Chouhan, Velaphi Msomi   +3 more
wiley   +1 more source

Effect of Post-Heat Treatment on Microstructure and Corrosion Property of Additively Manufactured AlCoCrFeNi_2.1 Eutectic High-Entropy Alloy. [PDF]

Materials (Basel)
Li X, Ding H, Pi X, Zhang S, Xie Y.
europepmc   +1 more source

Effect of Heat Treatment and Plasma Arc Welding on the Mechanical and Metallurgical Properties of Hastelloy C276

, 2020
U. Mohammed Iqbal, S Muralidharan
openalex   +1 more source

Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6

Advanced Engineering Materials, EarlyView.
The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter, Thomas Wegener, Andreas Schilling, Martin Fehlbier, Thomas Niendorf   +4 more
wiley   +1 more source

Effect of Cold-Sprayed Zinc Coating and Heat Treatment on the Microstructure and Corrosion Behavior of 30MnB5 Hot-Stamped Steel. [PDF]

Materials (Basel)
Nam H, Seo M, Park C.
europepmc   +1 more source

Design and Prototyping of Topology‐Optimized, Additively Manufactured Lightweight Components for Space Robotic Systems: A Case Study

Advanced Engineering Materials, EarlyView.
The results demonstrate a simulation‐driven workflow that applies LSB topology optimization with additive manufacturing constraints to mission‐specific load cases, integrating European Cooperation for Space Standardization compliant verification and manufacturability to develop structurally efficient rover suspension components.
Stelios K. Georgantzinos, Grigorios Kostopoulos, Eleni Papadopoulou, Stefanos Voulgaris, Alexandra Tseni, Panteleimon Bakalis, Maria N. Gkara, Chara Ch. Mitropoulou, Georgios Kazakis, Alin Munteanu, Jeremi Gancet, Nikos D. Lagaros   +11 more
wiley   +1 more source

Cellulosic Functional Bioplastic with Tunable Strength and Toughness Through Heat-Treatment of Dynamic Covalent Networks. [PDF]

Adv Sci (Weinh)
Tang X, Zhao L, Guo Y, Wang Y, Wei Z, Fan X, Xiao Z, Wang H, Xie Y, Wang Y.   +9 more
europepmc   +1 more source