Results 111 to 120 of about 31,808 (264)

Experimental Characterization of Mycelium‐Based Composites Under Multiple Loading Conditions

Advanced Engineering Materials, EarlyView.
This study examines the mechanical response of mycelium‐based composites under compression, shear, and tension using mechanical testing and imaging methods. The comparison between unpressed and hot‐pressed specimens shows that hot pressing is associated with higher compression and shear stiffnesses.
Shaghayegh Elahi, Kimiya Tajik, Harvey Shaw, Matti Isakov, Sami Pajunen, Lauri Rautkari   +5 more
wiley   +1 more source

Machine Learning‐Supported Analysis for Predicting and Visualizing Nonlinear Relationships Between Material Properties in Electroplated Chromium Layers

Advanced Engineering Materials, EarlyView.
This study applies machine learning regression to predict chromium layer thickness in decorative trivalent chromium electroplating, using 441 experiments from laboratory‐scale (1L) and pilot‐scale (14L) setups. Tree‐based models, particularly CatBoost, outperformed linear regression by capturing nonlinear parameter interactions (R2$R^2$ up to 0.77 ...
Christoph Baumer, Christopher Mai, Luca Eisentraut, Andreas Bund, Ricardo Buettner   +4 more
wiley   +1 more source

Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading

Advanced Engineering Materials, EarlyView.
This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev, Noah‐Lean Roschlaub, Anne Jung   +2 more
wiley   +1 more source

Influence of Si Content and Milling Duration on the Microstructure and Mechanical–Tribological Properties of AlCoCrFeNiSi High‐Entropy Alloys

Advanced Engineering Materials, EarlyView.
Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş, Mehmet Emin Demir, Sercan Özpınar   +2 more
wiley   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Evaluation of Microwave Heating Uniformity for Ready-to-Eat Rice in Metalized Packaging Structure. [PDF]

Foods
Liu C, Tian B, Liu H, Shen L, Zhu Y, Liu C, Zheng X, Deng X, Zhao Y.   +8 more
europepmc   +1 more source

Defect Evolution and Mechanical Performance of Fused Filament Fabrication‐Manufactured 17‐4PH Stainless Steel Revealed by X‐Ray Computed Tomography

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky, Márk Sárközi, Ibolya Zsoldos, Zoltán Weltsch   +3 more
wiley   +1 more source

Radio Frequency Vacuum Drying Study on the Drying Characteristics and Quality of Cistanche Slices and Analysis of Heating Uniformity. [PDF]

Foods
Chen A, Wan F, Ma G, Ma J, Xu Y, Zang Z, Ying X, Jia H, Huang X.   +8 more
europepmc   +1 more source

Active Corrosion Protection of Sintered AA7075 Aluminum Alloy via Mn Powder Addition

Advanced Engineering Materials, EarlyView.
AA7075 containing Mn‐rich particles is fabricated via spark plasma sintering using AA7075 and Mn powders. Corrosion resistance is evaluated through dip‐and‐dry tests using 0.1 M NaCl (pH 6.0), and mass loss decreases with increasing Mn addition. Mn‐rich particles function as a source of Mn ions, and formation of Mn‐accumulation films on Cu‐containing ...
Ko Ebina, Masashi Nishimoto, Izumi Muto
wiley   +1 more source

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source