Results 151 to 160 of about 86,221 (307)

Influence of Si Content and Milling Duration on the Microstructure and Mechanical–Tribological Properties of AlCoCrFeNiSi High‐Entropy Alloys

Advanced Engineering Materials, EarlyView.
Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş, Mehmet Emin Demir, Sercan Özpınar   +2 more
wiley   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Test and Study on Reheating Process of 280 mm x 380 mm Cast Bloom of Steel U75V for Heavy Rail

Teshugang, 2011
The 280 mm x 380 mm cast bloom temperature of steel U75V for heavy rail in walking beam reheating furnace has been traced and measured by using Thermophil STOR measure system (black box) at steel works, and the data are treated by Origin software to get ...
孙志亮, 杭乃勤, 李浩进
doaj  

Defect Evolution and Mechanical Performance of Fused Filament Fabrication‐Manufactured 17‐4PH Stainless Steel Revealed by X‐Ray Computed Tomography

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky, Márk Sárközi, Ibolya Zsoldos, Zoltán Weltsch   +3 more
wiley   +1 more source

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source

Full efficiency zone heating systems

, 1977
The advantages of high-efficiency fossil fuel-fired individual room space heaters which can burn clean fuels such as methanol, methane, or natural gas are discussed, and the overall design described. These heaters have an overall efficiency of virtually 100 percent, no duct losses, and are individually controlled. Further feasibility and design studies
openaire   +2 more sources

Laser‐Induced Graphene from Waste Almond Shells

Advanced Functional Materials, EarlyView.
Almond shells, an abundant agricultural by‐product, are repurposed to create a fully bioderived almond shell/chitosan composite (ASC) degradable in soil. ASC is converted into laser‐induced graphene (LIG) by laser scribing and proposed as a substrate for transient electronics.
Yulia Steksova, Anna Chiara Bressi, Marina Galliani, Attilio Marino, Gianni Ciofani, Eduardo Machado‐Charry, Hilda Gomez Bernal, Alessandra Francini, Luca Sebastiani, Francesco Greco   +9 more
wiley   +1 more source

Advances in Electrofusion Welding Technology for Polymeric Pipelines: From Process Optimization to Mechanism-Driven Control. [PDF]

Polymers (Basel)
Hong B, Sun Z, Wu Z, Meng Y, Chen Z, Chen X, Wang W, Liu D.   +7 more
europepmc   +1 more source

Mechanical Behavior and Fracture Mechanisms of MXene/PVDF Nanocomponsites: In Situ Characterization and Multiscale Analysis

Advanced Functional Materials, EarlyView.
Multiscale experiments and modeling reveal how Ti3C2Tx MXene nanosheets reinforce PVDF nanocomposites. An optimal MXene loading (∼1 wt.%) nearly doubles tensile strength through efficient stress transfer, flake alignment, and crack‐deflection mechanisms, transforming ductile polymer behavior into a controlled multi‐stage fracture pathway which aligns ...
Bita Soltan Mohammadlou, James FitzPatrick, Li Meng, Kateryna Shevchuk, Ahmad Najafi, Yury Gogotsi   +5 more
wiley   +1 more source

Receptor‐Free Identification of Toxic Gases Enabled by Hygroscopic Aqueous Salt Films

Advanced Functional Materials, EarlyView.
Water as a gas sensor coating sounds impossible—until it stops evaporating. Here, hygroscopic salt solutions (LiCl, LiBr, H3PO4) form non‐drying aqueous films on CNT chemiresistors under ambient air. Gases partition into these liquid layers, sometimes transforming into water, and generate salt‐specific resistance fingerprints across a four‐channel ...
Seongwoo Lee, Yun‐Tae Kim, Hwarang Choi, Sanghwan Park, Seongyeop Lim, Chang Young Lee   +5 more
wiley   +1 more source