Results 61 to 70 of about 152,702 (261)
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
HAZARD ANALYSIS OF CRITICAL CONTROL POINTS (HACCP) OF SOME POST HARVEST PESTICIDE IN ORANGE FRUIT [PDF]
Journal of Plant Protection and Pathology, 2002 The present work was conducted in one of an Egyptian food processors company with the purpose of identifying critical control points (CCP’s) and reducing pesticide residues contaminating incoming raw orange throughout the manufacturing steps.
Sohair Gad Alla
doaj +1 more source
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source
Additive Gaussian Process Regression for Predictive Design of High‐Performance, Printable Silicones
Advanced Engineering Materials, EarlyView.A chemistry‐aware design framework for tuning printable polydimethylsiloxane (PDMS) for vat photopolymerization (VPP) is developed using additive Gaussian process (GP) modeling. Polymer network mechanics informs variable groupings, feasible formulation constraints, and interaction variables.
Roxana Carbonell +3 more
wiley +1 more source
Strain hardening recovery mediated by coherent precipitates in lightweight steel
Scientific Reports, 2021 We investigated the effect of κ-carbide precipitates on the strain hardening behavior of aged Fe–Mn-Al-C alloys by microstructure analysis. The κ-carbides-strengthened Fe–Mn-Al-C alloys exhibited a superior strength-ductility balance enabled by the ...
Sung-Dae Kim +8 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi +2 more
wiley +1 more source
Scientific ReportsMepiquat (MPQ) is a quaternary ammonium salt widely used as a growth regulator in agriculture. A recent report from the European Union Reference Laboratory for Single Residue Methods (EURL SRM) reported MPQ residues in Egyptian sweet potatoes at levels ...
Mohamed Wageed +5 more
doaj +1 more source
Effect of Laser Deoxidation on Adhesive‐Bonded Aluminum in an Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.This study investigates laser ablation of aluminum under oxygen‐free conditions. The goal is to produce oxide‐free substrates that enable improved adhesive bonding with epoxy. Optimized laser parameters (90% overlap, 300 µJ) combined with oxide‐free substrates result in the highest tensile strength of the adhesive bond.
Sandra Gerland +5 more
wiley +1 more source
Removing Oxide Layers and Retaining Oxide‐Free Steel Surfaces by Polishing in Oxygen‐Free Atmosphere
Advanced Engineering Materials, EarlyView.In this study, the efficacy of wet mechanical polishing under an oxygen‐free atmosphere for deoxidation and the retention of an oxide‐free steel surface are elucidated using X‐ray photoelectron spectroscopy. The methodology proved successful; however, the results were highly dependent on the preparation of the solvents used to clean the samples after ...
Friedrich Bürger +2 more
wiley +1 more source