Results 101 to 110 of about 1,768 (208)

Mechanical and Metallurgical Evaluation of Four Rotary Nickel‐Titanium File Systems: A Multimethod Study

International Endodontic Journal, EarlyView.
ABSTRACT Aim To compare four rotary nickel‐titanium (NiTi) file systems (Endostar E3 Azure, Endostar E3, VDW.ROTATE, and Mtwo) using a multimethod approach to evaluate their mechanical and metallurgical properties. Materials and Methods Endostar E3 Azure, Endostar E3, VDW.ROTATE, and Mtwo (all size 25/0.06 with an S‐shaped cross‐section; 52 instruments
Doğuş Bayraktar, Uğur İnan
wiley   +1 more source

Anatomical Study of Lateral Compression II Screw Path and Entry Parameters Based on Three‐Dimensional CT Image Reconstruction Techniques

Orthopaedic Surgery, Volume 17, Issue 5, Page 1454-1463, May 2025.
This graphical abstract illustrates a study where 43 adult patients (21 males, 22 females) underwent CT scans to reconstruct 3D pelvic models using Mimics and 3‐Matic software. The analysis measured the Lateral Compression II (LC‐II) screw path, revealing sex‐based anatomical differences that could improve the precision and safety of percutaneous LC‐II
Xingye Du, Yong Liu, Xuefeng Jiang
wiley   +1 more source

A New Paradigm for Understanding the Rheology and Processability of Poly(p‐Phenylene Terephthalamide) Liquid‐Crystalline Solutions

Journal of Applied Polymer Science, Volume 143, Issue 34, September 10, 2026.
Kevlar is traditionally modeled as a rigid‐rod polymer, yet rheological behavior deviates from this assumption. The review introduces a novel “twist‐tie” entanglement theory for aramid polymer chains in the nematic liquid crystal state, providing a molecular explanation for deviations from rigid‐rod models. Understanding twist‐tie entanglement dynamics
Emma Egli, Jacob L. Pretko, Christopher W. Seay, Steven R. Lustig   +3 more
wiley   +1 more source

On the parametric analytics to investigate hole quality characteristics during helical milling of carbon fiber reinforced plastics stacks

AIP Advances
Dimensional inaccuracies are considered the primary challenge during the drilling of carbon fiber reinforced polymer materials to be employed in aeronautical applications.
Mehdi Tlija, Nimra Naeem, Mohammad Pervez Mughal, Kiran Mughal, Saad Ullah, Muhammad Sana, Anamta Khan   +6 more
doaj   +1 more source

3D imaging and mechanical modeling of helical buckling in Medicago truncatula plant roots. [PDF]

Proc Natl Acad Sci U S A, 2012
Silverberg JL, Noar RD, Packer MS, Harrison MJ, Henley CL, Cohen I, Gerbode SJ.   +6 more
europepmc   +1 more source

Concept, Tests, and Optimum Design of Novel Negative Stiffness Friction Dampers for Seismic Protection of Long‐Span Bridges

Earthquake Engineering &Structural Dynamics, Volume 55, Issue 11, Page 2719-2741, September 2026.
ABSTRACT Viscous dampers (VDs) are widely used to mitigate the excessive responses of long‐span bridges. However, VDs face some intricate challenges in engineering practices, including high damping coefficient requirement, potential base shear amplification and tremendous damping force under high velocity. To address these issues, this study develops a
Ruisheng Ma, Shaodong Jiang, Kun Xu, Qiang Han, Xiuli Du, Kaiming Bi   +5 more
wiley   +1 more source

Quantifying Soft‐Surgery in Cochlear Implantation: Multimodal Data From 30 International Specialists

The Laryngoscope, Volume 136, Issue 9, Page 3990-3997, September 2026.
Objective data from 30 specialist cochlear implant surgeons showed that surgical handling strongly influences intracochlear mechanical stress during implantation. Surgeons with fewer than 50 lifetime insertions performed significantly worse than more experienced colleagues, while self‐assessment did not reflect objective performance in any group ...
Philipp Aebischer, Georgios Mantokoudis, Marco Caversaccio, Stefan Weder   +3 more
wiley   +1 more source

Advanced Electrospun Nanofiber Epidermal Electronics for Electrophysiological Monitoring: From Conformal Interfaces to Multimodal Closed‐Loop Systems

Rare Metals, Volume 45, Issue 9, September 2026.
ABSTRACT Epidermal bioelectronics is a transformative technology for continuous health monitoring and human‐computer interaction. However, the mechanical and physiological mismatch at the skin–device interface limits its long‐term application. Electrospun nanofiber membranes (ENMs), with their unique three‐dimensional hierarchical porous network and ...
Jiahua Ni, Jing Lu, Nianzhe Wu, Jiahui Tang, Tiantian Chen, Xiaonong Zhang, Wenhui Wang, Zhe Zhao   +7 more
wiley   +1 more source

Assessing and Quantifying Variability Across Vacuum‐Assisted Resin Infusion Variants for Aerospace‐Grade Composite Manufacturing

Polymer Composites, Volume 47, Issue 15, Page 13664-13684, 10 August 2026.
Radar‐plot comparison of consolidation quality and flexural performance of composite laminates manufactured by six vacuum‐infusion routes, evaluated at the resin‐inlet and vacuum‐port regions. ABSTRACT Conventional vacuum‐assisted resin transfer molding (C‐VARTM) is recognized as a cost‐effective resin infusion technique for manufacturing large‐scale ...
Ilhan Kahraman, Nilperi Uysal, Çağlar Subaşı, Selin Dursun, Muhammet İskender, Özgü Çalın, Uğur Şimşir, Hatice S. Sas, A. Tuğrul Seyhan   +8 more
wiley   +1 more source

Manufacturability‐Aware Multi‐Objective Screening of Filament‐Wound Type IV Pressure‐Vessel Cylindrical Sections Using Dual‐Pressure Hashin Constraints

Polymer Composites, Volume 47, Issue 15, Page 13854-13875, 10 August 2026.
Manufacturability‐aware multi‐objective screening of Type IV filament‐wound composite pressure‐vessel cylindrical sections toward lightweight and high‐strength designs. ABSTRACT A manufacturability‐aware preliminary screening framework is proposed for the straight cylindrical section of filament‐wound Type IV composite pressure vessels.
Önder Albayrak, Ahmet Çalık
wiley   +1 more source