Results 51 to 60 of about 23,710,206 (290)
A laser master oscillator power amplifier (MOPA) system consisting of a fiber amplifier and a two-stage Yb:YAG single crystal fiber (SCF) is experimentally studied.
Feng Li +8 more
doaj +1 more source
Laser‐Induced Graphene from Waste Almond Shells
Almond shells, an abundant agricultural by‐product, are repurposed to create a fully bioderived almond shell/chitosan composite (ASC) degradable in soil. ASC is converted into laser‐induced graphene (LIG) by laser scribing and proposed as a substrate for transient electronics.
Yulia Steksova +9 more
wiley +1 more source
Single Trench Fiber-Enabled High-Power Fiber Laser
As a novel design of large-mode-area fiber, the single trench fiber (STF) providing high higher-order-mode suppression with a large mode area for the fundamental mode shows potential for high-power and high-brightness applications.
Yi An +11 more
doaj +1 more source
Optoelectronic synaptic devices based on solution‐processed molecular telluride GST‐225 phase‐change inks are demonstrated for three‐factor learning. A global optical signal broadcast through a silicon waveguide induces non‐volatile conductance updates exclusively in locally electrically flagged memristors.
Kevin Portner +14 more
wiley +1 more source
Broadband diode-pumped ytterbium-doped fiber amplifier with 34 dBm output power [PDF]
We investigate a high-power diode-pumped double-clad ytterbium-doped fiber amplifier with 34 dBm average output power and 1050 - 1095 nm bandwidth. A multi-diode concentrator pumps the amplifier at 980 nm, with ~6 W of power launched into the inner ...
Renaud, C.C. +17 more
core +1 more source
High-Power GHz Burst-Mode All-Fiber Laser System with Sub 300 fs Pulse Duration
An all-fiber low-repetition-rate SESAM mode-locked fiber oscillator combined with a dispersion-managed active fiber loop produces a flexible GHz burst-mode laser source. The high-power output is then produced by amplifying the GHz burst-mode laser source
Feng Li +9 more
doaj +1 more source
Advances in Sustainable and Wearable Textile Based Soft Robotics
This Review examines advances in wearable textile‐based soft robotics, focusing on sustainable materials, integrated sensing, and scalable actuation. It discusses manufacturing and system integration across healthcare, assistive robotics, prosthetics, and human–machine interfaces, and highlights key challenges in circular design, including life‐cycle ...
Zahir Abbas +6 more
wiley +1 more source
Depressed clad hollow optical fiber with fundamental LP01 mode cut-off
We propose a depressed clad hollow optical fiber with fundamental (LP01) mode cut-off suitable for high power short-wavelength, especially three-level, fiber laser operation by introducing highly wavelength dependent losses at longer wavelengths. The cut-
Codemard, C. +15 more
core +1 more source
Fiber design for high-power low-cost Yb:Al-doped fiber laser operating at 980nm [PDF]
We investigated an Yb:Al-doped depressed-clad hollow optical fiber (DCHOF) for cladding-pumped 980nm laser operation. With a careful design, the nonzero fundamental-mode cutoff characteristics of a DCHOF allows the competing 1030-1060nm emission to be ...
Kim, J. +4 more
core +1 more source
Composite fiber Bragg grating written by femtosecond laser for Raman suppression in high-power fiber oscillators [PDF]
High-power fiber oscillators have been widely used in industrial processing, high-end manufacturing, biomedicine and so on. However, as the output power increase, stimulated Raman scattering (SRS) becomes the main factor limiting the performance ...
Hao Li +9 more
doaj +1 more source

