Results 61 to 70 of about 118,466 (337)
Metals, 2023 AlSi12(Fe), AlSi10Mg(Fe), AlSi10MnMg, and AlMg4Fe2 die-casting alloys were produced by high-pressure die casting (HPDC) and vacuum-assisted high-pressure die casting (VADC) under a vacuum level of 200 mbar.
Gonçalo Soares +6 more
doaj +1 more source
Analytical Cost Estimation Model in High Pressure Die Casting
Procedia Manufacturing, 2017 Abstract The present paper aims at the definition of an analytical model for the cost estimation of the High Pressure Die Casting (HPDC) process. The model is based on two main pillars: (i) knowledge formalization and (ii) cost estimation algorithms.
Favi, Claudio +2 more
openaire +2 more sources
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé +5 more
wiley +1 more source
Effect of Selected Parameters of Pressure Die Casting on Quality of AlSi9Cu3 Castings
Archives of Foundry Engineering, 2015 This paper presents the results on the effects of die-casting process on the strength parameters of castings of the aluminium AlSi9Cu3 alloy belonging to the group of EN AB-46000, made on renovated high pressure die-casting machine. Specimens for quality
Pałyga Ł., Stachowicz M., Granat K.
doaj +1 more source
Case-based product development of a high-pressure die casting injection subset using design science research [PDF]
, 2022 Matilde Tojal +4 more
openalex +1 more source
A control and monitoring oriented model of a film manufacturing process [PDF]
, 2008 This paper describes the development of a control and monitoring oriented model of a plastic film manufacturing process. The model is mainly derived from first-principles and has been implemented in the Matlab/Simulink dynamic simulation environment. The
Balderud, Jonas +3 more
core +1 more source
Zein‐Based Adhesives: Sustainable Extraction and Application in Bioadhesive Technologies
Advanced Engineering Materials, EarlyView.Zein is extracted from corn gluten meal using a simple and scalable process with high yield (~90%). The resulting protein is applied in bioadhesives modified with Ca2+ and Fe3+ ions, exhibiting substrate‐dependent adhesion. The findings demonstrate competitive bonding performance and highlight the role of ionic interactions in tuning adhesion ...
Paula Bertolino Sanvezzo +3 more
wiley +1 more source
Metal Laminated Tooling - A Quick and Flexible Tooling Concept [PDF]
, 2004 For the fast manufacturing of complex formed tools Fraunhofer IWS works together with partners from the industry on a constant automation solution for cutting, packaging and adding steel sheet cutouts.
Beyer, Eckhard +3 more
core +1 more source
Advanced Engineering Materials, EarlyView.The thermal diffusivity of MgO‐C refractories is highly sensitive to sample preparation and processing procedures. In this article, the effects of coking sequence, machining conditions, structural inhomogeneity, and graphite coating application on measurements using laser flash apparatus are systematically investigated.
Luyao Pan +4 more
wiley +1 more source