Results 131 to 140 of about 88,882 (284)

Comparative Analysis of the Influence of Chemical Composition and Microstructure on the Abrasive Wear of High-Strength Steels. [PDF]

Materials (Basel), 2022
Zemlik M, Konat Ł, Napiórkowski J.
europepmc   +1 more source

Interaction between Molten Al‐Killed Mn–B Steel and Carbon‐Bonded MgO Refractories Based on Recyclates

Advanced Engineering Materials, EarlyView.
High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé, Lukas Neubert, Anton Yehorov, Till M. J. Stadtmüller, Christos G. Aneziris, Olena Volkova   +5 more
wiley   +1 more source

Comparison of Hydrogen Embrittlement Susceptibility of Different Types of Advanced High-Strength Steels. [PDF]

Materials (Basel), 2022
Cho S, Kim GI, Ko SJ, Yoo JS, Jung YS, Yoo YH, Kim JG.   +6 more
europepmc   +1 more source

Microstructural Evolution and Vacancy Defect Formation in Mn–Mo–Ni RPV Steel Under Low Cycle Fatigue: Insights From EBSD and PALS

Advanced Engineering Materials, EarlyView.
Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar, Dhanadeep Dutta, G. Bharat Reddy   +2 more
wiley   +1 more source

The Influence of Hot-Dip Galvanizing on the Mechanical Properties of High-Strength Steels. [PDF]

Materials (Basel), 2021
Šmak M, Kubíček J, Kala J, Podaný K, Vaněrek J.   +4 more
europepmc   +1 more source

Four‐Point Bending Tests at High Temperatures on Commercial MgO‐C Refractory Bricks with and Without Recyclate Considering Different Carbon Contents

Advanced Engineering Materials, EarlyView.
Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm, Lukas Knöchel, Thomas Schemmel, Christos G. Aneziris, Anja Weidner, Horst Biermann   +5 more
wiley   +1 more source

Chemical heterogeneity enhances hydrogen resistance in high-strength steels. [PDF]

Nat Mater, 2021
Sun B, Lu W, Gault B, Ding R, Makineni SK, Wan D, Wu CH, Chen H, Ponge D, Raabe D.   +9 more
europepmc   +1 more source

Population of Nonmetallic Inclusions in Liquid High‐Silicon Electrical Steel in Contact With MgO–C Refractories Based on Recyclates and Environmentally Friendly Binders

Advanced Engineering Materials, EarlyView.
The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert, Matheus Roberto Bellé, Florian Kerber, Dinesh Kumar Gunasekar, Hans‐Jörn Weddige, Christos G. Aneziris, Olena Volkova   +6 more
wiley   +1 more source

Integrated Machine Vision System for Evaluating Hole Expansion Ratio of Advanced High-Strength Steels. [PDF]

Materials (Basel), 2022
Park J, Won C, Lee HJ, Yoon J.
europepmc   +1 more source

3D‐Printed Serial Snap‐Through Architectures for Programmable Mechanical Response

Advanced Engineering Materials, EarlyView.
A serial snap‐through architecture is realized using compact 3D‐printed von Mises truss units arranged in a staged cascade. Their geometry and boundary conditions program multistage mechanical responses with plateaux and re‐hardening regimes. An inverted‐compliance model predicts these behaviors and enables analytical design of programmable force ...
Filipe A. Santos
wiley   +1 more source