Surface Potential Decay of Gamma-Irradiated Low-Density Polyethylene [PDF]
, 2009 In the present paper the surface potential decay after dc corona charging of gamma-irradiated low-density polyethylene (LDPE) has been studied. The irradiation was carried out in air, nitrogen gas and vacuum to investigate the effect of irradiation ...
Chen, George
core +2 more sources
ELECTROSTATIC CHARGE GENERATED FROM SLIDING OF HIGH DENSITY POLYETHYLENE AGAINST AIR BUBBLE SHEET OF LOW DENSITY POLYETHYLENE [PDF]
Journal of the Egyptian Society of Tribology, 2017 The present work investigates the electrostatic charge (ESC) generated from contact and separation as well as sliding of high density polyethylene (HDPE) on the air bubble sheets. They are made of low-density polyethylene (LDPE) of air-bubbles. They have
A. S. Ali, A. Alahmadi, W. Y. Ali
doaj +1 more source
NON-BIODEGRADATION OF POLYMERIZED POLYETHYLENE RADICALS AT SELECTED DUMPSITES IN KEFFI, NASARAWA STATE NIGERIA [PDF]
Journal CleanWAS, 2023 Polythene and plastic bags pollutes the soil because these are non-biodegradable, and so, they cannot be degraded by the action of the microbes. Therefore, they remain in the soil and will pollute the soil.
Sufiyan I., Salamatu A. E., Alkali M
doaj +1 more source
High density polyethylene and zirconium phosphate nanocomposites
Polímeros, 2015 Nanocomposite based on high density polyethylene (HDPE) and layered zirconium phosphate organically modified with octadecylamine (ZrPOct) was obtained through melt processing.
Adan Santos Lino +3 more
doaj +1 more source
Mechanical properties of filled high density polyethylene
Journal of Saudi Chemical Society, 2015 Mechanical properties of (HDPE M624) with three filler (inorganic and organic) composites were assessed with respect to the effect of the filler content. The filler varied from (5% to 25%) by weight in the composite. Obvious improvement in the mechanical
Moayad N. Khalaf
doaj +1 more source
Thermal effects in high density polyethylene and low density polyethylene at high hydrostatic pressures [PDF]
Journal of Materials Science, 1987 The temperature changes as a result of rapid hydrostatic pressure applications are reported for high density polyethylene (HDPE) and low density polyethylene (LDPE) in the reference temperature range from 298 to 423 K and in the pressure range from 13.8 to 200 MN m−2.
Rodriguez, Ernesto L., Filisko, Frank E.
openaire +2 more sources
Kinetic modelling of phenols consumption during polyethylene thermal oxidation [PDF]
, 2013 Irganox 1010 stabilized PE was monitored by carbonyl build-up and DSC under oxygen. A scheme for PE stabilization by phenols was implemented and its kinetic parameters were calculated from experimental results.
RICHAUD, Emmanuel
core +1 more source
The effect of gamma irradiation on space charge behaviour and dielectric spectroscopy of low-density polyethylene [PDF]
, 2007 The influence of gamma irradiation on low-density polyethylene (LDPE) has been studied through space charge measurement and dielectric spectroscopy. Commercial LDPE film with a thickness of 100µm was irradiated with γ-rays at a dose rate of approximately
Dissado, L. A. +4 more
core +2 more sources
Fotodegradasi High Density Polyethylene Yang Mengandung Aditif Okso-Biodegradasi
Indonesian Journal of Chemical Research, 2017 High Density Polyethylene (HDPE) is a type of plastic that widely used for packaging because it has good mechanical properties. HDPE is naturally non-biodegradable, and the consequence it will increase plastic waste that will damage the environment.
Ristika O. Asriza, Janiar Pitulima
doaj +1 more source
FRICTION AND WEAR OF POLYMERIC MATERIALS REINFORCED BY CARBON NANOTUBES [PDF]
Journal of the Egyptian Society of Tribology, 2017 The present work studies friction coefficient and wear of polymeric materials such as high density polyethylene (HDPE), low density polyethylene (LDPE) and polystyrene (PS). The polymers are filled by carbon nanotubes (CNTs) in concentration up to 1.0 wt.
H. S. Eatemad +3 more
doaj +1 more source