Enhancing Long Stability of Solid-State Batteries Through High-Energy Ball Milling-Induced Decomposition of Sulfide-Based Electrolyte to Sulfur. [PDF]
Adv MaterQian X +6 more
europepmc +2 more sources
Archives of Metallurgy and Materials, 2015 In this research, effect of the various mechanical milling process on morphology and microstructural changes of nano and micron Al-powders was studied. The milling of Al-powders was performed by both high energy and low energy ball milling process.
Kim H.-S. +6 more
doaj +1 more source
Journal of MMIJ, 2022 The high-pressure grinding roll (HPGR) has been known to achieve a high mineral liberation with relatively low energy consumption. However, quantitative methods for evaluating the effect of HPGR grinding on the promotion of the mineral liberation of ...
Yuki TSUNAZAWA +8 more
doaj +1 more source
Synthesis of SnSb2Te4 Microplatelets by High-energy Ball Milling [PDF]
Materials Research, 2015 In this work we demonstrate that high-energy ball milling process can be used to synthesize SnSb2Te4 without surfactant and further annealing. Milling parameters such as ball to raw material ratio (5:1) and milling time (2h) were determined to be ...
Mário Sérgio da Luz +5 more
doaj +2 more sources
New CaO-based adsorbents prepared by solution combustion and high-energy ball-milling processes for CO2 adsorption: Textural and structural influences [PDF]
, 2017 New CaO-based adsorbents prepared by solution combustion and high-energy ball-milling processes for CO2 adsorption: Textural and structural influencesIn the present work, new CaO-based adsorbents were obtained by a fast solution combustion method and ...
GRANADOS CORREA, FRANCISCO +7 more
core +1 more source
Development and Characterization of Mg-SiC Nanocomposite Powders Synthesized by Mechanical Milling [PDF]
, 2017 Dieser Beitrag ist mit Zustimmung des Rechteinhabers aufgrund einer (DFG geförderten) Allianz- bzw. Nationallizenz frei zugänglich.This publication is with permission of the rights owner freely accessible due to an Alliance licence and a national licence
Fleck, Claudia +4 more
core +1 more source
Characterization of nanodimensional Ni-Zn ferrite prepared by mechanochemical and thermal methods. [PDF]
, 2010 Nickel zinc ferrite nanoparticles, Ni1−xZnxFe2O4 (x = 0, 0.2, 0.5, 0.8, 1.0), with dimensions below 10 nm have been prepared by combining chemical precipitation with high-energy ball milling.
B Kunev +6 more
core +1 more source
Dehydroxylation of high-energy ball-milled diasporic bauxite
Journal of Thermal Analysis and Calorimetry, 2018 In this study, diasporic bauxite was mechanically activated for different durations (15, 30, 60, 90 and 120 min) by the planetary mono mill. The speed of the main disk and ball-to-mass ratio were kept constant at 600 rev min−1 and 25, respectively. The chemical composition of the ore was determined via X-ray fluorescence. Structural changes and thermal
Volkan Murat Yilmaz +2 more
openaire +5 more sources
Optimization of the AISI 52100 steel processed by high energy ball milling [PDF]
REM: International Engineering JournalAISI 52100 steel is an alloy steel with a high carbon and chromium content, widely used in industry to produce bearings. Through high energy ball milling, it is possible to obtain powders in submicrometer scale for later use in a new product using powder
Bruna Horta Bastos Kuffner +2 more
doaj +2 more sources
Optimization for preparing Bi1.68Pb0.32Sr1.75Ca1.85Cu2.85O10+y powders by wet ball milling
Materials Research Express, 2022 Superconducting Bi _1.68 Pb _0.32 Sr _1.75 Ca _1.85 Cu _2.85 O _10+ _y (Bi-2223) powders were prepared by a conventional solid-state reaction using hand grinding and wet ball milling.
Yingwei Chen +8 more
doaj +1 more source