Results 181 to 190 of about 1,751,206 (262)

Symmetry classification of magnetic orders using oriented spin space groups. [PDF]

Nature
Liu Y, Chen X, Yu Y, Etxebarria J, Perez-Mato JM, Liu Q.   +5 more
europepmc   +1 more source

Influence of Sample Preparation and Processing Procedures on the Thermal Diffusivity of MgO‐C Refractories

Advanced Engineering Materials, EarlyView.
The thermal diffusivity of MgO‐C refractories is highly sensitive to sample preparation and processing procedures. In this article, the effects of coking sequence, machining conditions, structural inhomogeneity, and graphite coating application on measurements using laser flash apparatus are systematically investigated.
Luyao Pan, Rhena Wulf, Till M. J. Stadtmüller, Christos G. Aneziris, Tobias M. Fieback   +4 more
wiley   +1 more source

Multi-facility virtual diagnostic for longitudinal phase space predictions. [PDF]

Sci Rep
Lundquist J, Björklund Svensson J, Dijkstal P, Mansten E, Penco G, Werin S, Curbis F.   +6 more
europepmc   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Tribological Performance of 60NiTi Alloy Under Varying Contact Conditions and Elevated Temperatures in Linear Reciprocating Sliding

Advanced Engineering Materials, EarlyView.
This study investigates the tribological response of 60NiTi alloy under dry, water‐lubricated and high‐temperature conditions. The alloy exhibits decreasing wear volume and friction with increasing temperature due to the formation of protective oxide layers. The work clarifies dominant wear mechanisms and demonstrates the suitability of 60NiTi for high‐
Anthony Onyebuchi Okoani, Miguel Angel Selles, Maziar Ramezani   +2 more
wiley   +1 more source

Transparent reporting of group-based trajectory modeling to study medication adherence: Practical considerations and common pitfalls. [PDF]

J Manag Care Spec Pharm
Rizk JG, Qato DM.
europepmc   +1 more source

Characterization of Nitinol Produced by Laser Powder Bed Fusion for Mechanical Metamaterial Applications

Advanced Engineering Materials, EarlyView.
Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek, Jakub Hurník, Miroslav Šmíd, Ondřej Zobač, Melanie Todt, Daniel Koutný   +5 more
wiley   +1 more source

External-knowledge enhanced dual encoder and contrastive learning for aspect sentiment triplet extraction. [PDF]

PLoS One
Huang Y, Zhou X, Yin R, Shi P.
europepmc   +1 more source

EBSD Study of Creep‐Induced Lattice Misorientation in MgO‐Particle‐Reinforced Austenitic Steel Composites

Advanced Engineering Materials, EarlyView.
Creep experiments at 900°C on coarse‐grained steel‐ceramic composites containing recycled magnesia reveal that higher ceramic volume fractions significantly enhance the creep resistance. Detailed EBSD investigations identify subgrain formation in the steel matrix as the dominant deformation mechanism.
Moritz Müller, Amaya Compart, Mahnaz Mehdizadehlima, Serhii Yaroshevskyi, Christos G. Aneziris, Horst Biermann, Anja Weidner   +6 more
wiley   +1 more source

Comparative analysis of fractional thermoelastic vibrations of a nonlocal nanobeam exposed to travelling and static thermal loads. [PDF]

Sci Rep
Tiwari R, Gupta GK, Shivay ON.
europepmc   +1 more source