Results 131 to 140 of about 164,762 (278)
Effect of Oxygen Content on Surface and Subsurface Integrity During Turning of Ti–6Al–4V
Advanced Engineering Materials, EarlyView.This study examines how oxygen content in the ambient atmosphere affects the surface and subsurface properties of Ti–6Al–4V during turning. Results show that oxygen does not influence surface roughness. However, machining in an extremely high vacuum‐adequate atmosphere increases surface hardness by up to 7.8% and induces compressive residual stresses ...
Benjamin Bergmann +3 more
wiley +1 more source
On Holder continuity of solutions of the Beltrami equations
Herald of Dagestan State University, 2016 M.M. Sirazhudinov +2 more
openaire +1 more source
HOLDER CONTINUITY FOR LYAPUNOV EXPONENTS OF RANDOM LINEAR COCYCLES [PDF]
, 2021 openaire +1 more source
Advanced Engineering Materials, EarlyView.Trace additions of Sn and Sr combined with a two‐step aging treatment are shown to enhance the microstructure and performance of Al–Zr–Sc conductor alloys. Strength and electrical conductivity increase concurrently through accelerated precipitation of fine Al3(Sc, Zr) precipitates and improved dislocation resistance, offering a cost‐effective pathway ...
Quan Shao +3 more
wiley +1 more source
Local differentiability for the solutions to basic systems of higher order
Le Matematiche, 1987 In this paper we show a local differentiability result and a fundamental estimate for the solutions to non linear basic systems of higher order. Tese results are preliminary to the study of the quasi-holder continuity for non linear parabolic systems of ...
Roberto Amato
doaj
Advanced Engineering Materials, EarlyView.A hierarchical porous copper current collector is fabricated via three‐dimensional printing combined with pressureless sintering to stabilize lithium metal anodes. The interconnected architecture lowers local current density, guides uniform Li deposition within pores, and suppresses dendrite growth.
Alok Kumar Mishra, Mukul Shukla
wiley +1 more source
Near‐Field Electrospinning Micro‐Printhead Achieves Precise Control of Nanofiber Deposition
Advanced Engineering Materials, EarlyView.A micro‐printhead for near‐field electrospinning enables reproducible deposition of polymer nanofibers with diameters below 50 nm. Systematic parameter studies uncover the mechanisms linking operating conditions to fiber morphology, paving the way for precise and low‐cost nanoscale 3D manufacturing.As a high‐resolution, cost‐effective, and rapid ...
Han Xu, Dario Mager, Jan G. Korvink
wiley +1 more source
On Newton's method for operators with Hölder continuous derivative
Journal of Numerical Analysis and Approximation Theory, 1993 The author obtains some results concerning the convergence of Newton's method for solving operator equations in Banach spaces, when the first Fréchet-derivative of the operator involved is only Hölder continuous. In the case when the Hölder condition is a Lipschitz one, one of the theorems reduces to the Kantorovich theorem.
openaire +3 more sources
Advanced Engineering Materials, EarlyView.Disordered (Fe50Co50)1−xPtx thin films exhibit a pronounced anomalous Nernst effect (ANE) with a strong composition dependence on both rigid and flexible substrates. The transverse thermoelectric response peaks near 22.5 at.% Pt, accompanied by enhanced αxy/σxy scaling, thermal transport, and ANE sensitivity.
Mojtaba Mohammadi +2 more
wiley +1 more source
Setup‐Optimized Sequencing in Job Shops: Modeling Workstation Productivity and Lateness Behavior
Advanced Engineering Materials, EarlyView.Setup‐optimized sequencing in job‐shop production creates a trade‐off between productivity improvement and schedule reliability. A WIP‐explicit modeling framework links sequencing‐induced productivity gains and lateness dispersion through the production operating curve.
Friederike Stefanowski +2 more
wiley +1 more source